Steel beam replacement & repair · Exeter
Steel beam replacement & repair in Exeter
Steel beam replacement & repair for homes in EX1, EX2, EX4, designed by a structural engineer.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Exeter and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our steel beam replacement & repair service in Exeter
Our steel beam replacement & repair service in Exeter covers everything from the first visit to the completion paperwork. We also cover the surrounding towns and villages in Devon. Postcode districts we cover here include EX1, EX2 and EX4.
Not every steel beam was put in properly. Some were fitted decades ago without calculations, some sit on crumbling brick or timber packing, and some have rusted where water reached them through a leaking roof, a shopfront or a damp wall. Cracks in the plaster above, doors that stick or a visible dip are common warning signs.
Things to plan for
- A repair only lasts if the cause is dealt with too. A leaking roof, blocked gutter or bridged damp-proof course that rusted the beam needs fixing first, otherwise new protective coatings will break down in the same way.
- Corrosion usually starts where water reaches the steel: under a leaking flat roof, behind a shopfront fascia, in a damp external wall or at a cellar ceiling. Light surface rust can often be cleaned and treated, while heavy loss of section changes the beam's strength.
- Many problem beams are not faulty steel at all but poor bearings. Ends resting on loose brick, timber offcuts or no padstone can crush the masonry beneath, and the beam then drops slightly and cracks the finishes above.
- Beams fitted without calculations, whether decades ago or more recently without approval, may be smaller than the loads require, particularly in shop conversions and older knock-throughs. An engineer can check the existing section against the actual loads and say whether it is adequate.
- Like-for-like repainting needs no approval, but strengthening, rebuilding bearings or replacing a beam is structural work that falls under building control. Where an earlier beam went in without approval, a regularisation application in England and Wales can be used to seek retrospective sign-off.
How the job runs in Exeter
Survey in Exeter
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Exeter?
As a guide, budget £2,050–£5,650 including VAT for steel beam replacement in Exeter, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steel beam replacement | £2,050–£5,650 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Building control fees | £260–£670 | Building notice or full plans fee and inspections; varies by council or approver |
| Fire protection to a steel beam | £150–£620 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Temporary works and propping | £150–£520 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Approvals in Exeter
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Questions about steel beam replacement & repair in Exeter
Can you work on older or listed homes in Exeter?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Do you cover Exeter for steel beam replacement & repair?
Yes. We carry out steel beam replacement & repair in Exeter and the EX1, EX2 and EX4 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Is it cheaper to repair or replace a steel beam?
Repair is often less disruptive and can cost less, but only when the engineer confirms it will do the job. Heavily corroded or badly undersized beams may need replacing anyway, and plating in awkward positions is not always cheaper. We price the option the engineer specifies in an itemised written quote.
Can an old shop beam be replaced while the flat above is occupied?
Often, yes, with careful planning. The front wall and floors above are propped from inside the shop, and sometimes from outside, before the old beam is cut out. Occupants can often stay in if the engineer is satisfied with the propping, though there will be noise for a few days. Where the flat is separately owned, access and consents need agreeing in advance.
Can a rusty steel beam be repaired?
Often, yes. Surface rust can usually be cleaned back to sound steel and treated with a protective coating. Where corrosion has eaten into the flanges or web, the engineer works out the remaining strength and decides whether plating will restore it or the beam needs replacing. The source of the moisture must be fixed as well.
Who approves steel beam replacement & repair in Exeter?
Structural work in Exeter needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.