Structural calculations · Exeter
Structural calculations in Exeter
Structural calculations in Exeter, from free survey to completion certificate.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Exeter and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Structural calculations in Exeter: how it works
If you live in Exeter, structural calculations can usually be planned and priced after a single survey visit. Our coverage runs across Devon, so nearby villages are included too. We cover EX1, EX2 and EX4, and we fix the price in writing once the layout and scope are agreed.
We arrange the calculations as part of every structural job, or work to calculations you already have if they match the design. The engineer's output goes to building control with the application, and the same figures guide the steel order, the padstones and the propping on site.
Key points for your project
- If you already have calculations from your own engineer or architect, we can work to them, provided they match the layout being built. We check that the spans, loads and bearings shown agree with what is on site before ordering steel.
- Keep the final calculations and drawings with the building control completion certificate. Together they show a future buyer, lender or surveyor exactly what was installed and why, and they help any later alterations to build on a known design.
- A load take-down traces every weight that reaches the beam, from roof tiles and snow to upstairs walls, furniture and people. Getting this right matters as much as the beam choice itself, because an underestimated load makes every later check wrong.
- The cost of calculations rises with complexity: the number of beams and columns, whether loads come down from several floors, whether foundations need designing, and how much investigation is needed on site. A single straightforward beam sits at the simpler end.
- Accurate site information is essential. The engineer needs real spans, joist directions, wall build-ups and what sits above, so a site visit or detailed survey usually comes before any calculations. Guesswork from estate agent floor plans is not enough.
What happens, step by step
Survey in Exeter
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for structural calculations in Exeter
As a guide, budget £260–£770 including VAT for structural calculations for a beam in Exeter, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Structural calculations for a beam | £260–£770 | Site measure or photos, beam and padstone design and calculations for building control |
| Loft conversion steels | £2,600–£6,200 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Load-bearing wall removal with steel beam | £2,050–£5,150 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Temporary works and propping | £150–£520 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Approvals in Exeter
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Structural calculations in Exeter: your questions
How much do structural calculations cost in Exeter?
As a guide, budget £260–£770 including VAT for structural calculations for a beam in Exeter, based on published UK cost guides adjusted for prices in the South West (+3%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
What happens at the survey visit in Exeter?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Can I use calculations from my architect or previous builder?
Yes, as long as they match what is actually being built. We check the spans, loads and bearing details against the layout and the site before ordering steel. If the plans have changed since the calculations were done, or the site differs from what was assumed, the engineer needs to update them first.
What is a load take-down?
A load take-down is the part of the calculations that adds up every load reaching a beam or column and follows it down to the ground. It includes the roof, floors, walls, people, furniture and, where relevant, snow and wind. Each element along that path is then checked to make sure it can carry its share.
Do I need calculations for an old beam when selling my house?
Often a buyer's surveyor or solicitor will ask for them if there is no record of the beam being approved. An engineer can inspect the existing steel, check it against the loads and issue calculations or a report. In England and Wales these can support a regularisation application for retrospective approval.