Steel beam replacement & repair · Heavitree
Steel beam replacement & repair in Heavitree
Steel beam replacement & repair for homes in EX1, EX2, EX3, designed by a structural engineer.
- Free survey visit in Heavitree
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our steel beam replacement & repair service in Heavitree
Our steel beam replacement & repair service in Heavitree covers everything from the first visit to the completion paperwork. It sits about 1.4 miles from Exeter, which we also cover. Postcode districts we cover here include EX1, EX2, EX3 and EX4.
We start with a survey visit, arrange an engineer's inspection, then carry out whatever repair the engineer specifies, from new bearings to strengthening or full replacement. We handle building control and the temporary propping, and you get an itemised written quote before anything starts.
Key points for your project
- Older beams were often left with no fire protection or boxed in ordinary materials. When a beam is repaired or replaced, the fire protection is brought up to what the engineer and building control specify, commonly fire-rated plasterboard or intumescent paint.
- A repair only lasts if the cause is dealt with too. A leaking roof, blocked gutter or bridged damp-proof course that rusted the beam needs fixing first, otherwise new protective coatings will break down in the same way.
- Shop beams over old shopfronts are a common repair job. They often carry the whole front wall of the upper floors, sit behind fascias where rain gets in, and may have been cut or altered when shopfronts were replaced in the past.
- Many problem beams are not faulty steel at all but poor bearings. Ends resting on loose brick, timber offcuts or no padstone can crush the masonry beneath, and the beam then drops slightly and cracks the finishes above.
- Whether to strengthen or replace is the engineer's decision. Plating, where steel plates are fixed to the flanges, can add capacity without removing the beam, but it is not suitable for every section, connection or level of damage.
From survey to sign-off in Heavitree
Free visit
A short visit to Heavitree to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
What does steel beam replacement & repair cost in Heavitree?
As a guide, budget £2,050–£5,650 including VAT for steel beam replacement in Heavitree, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steel beam replacement | £2,050–£5,650 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Temporary works and propping | £150–£520 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| RSJ supply and fit (single beam) | £820–£2,580 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Fire protection to a steel beam | £150–£620 per beam | Fire-rated board boxing or an intumescent coating system as specified |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Building control and neighbours in Heavitree
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Questions about steel beam replacement & repair in Heavitree
Can you work on older or listed homes in Heavitree?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Who approves steel beam replacement & repair in Heavitree?
Structural work in Heavitree needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Can a rusty steel beam be repaired?
Often, yes. Surface rust can usually be cleaned back to sound steel and treated with a protective coating. Where corrosion has eaten into the flanges or web, the engineer works out the remaining strength and decides whether plating will restore it or the beam needs replacing. The source of the moisture must be fixed as well.
Can you replace a steel beam without taking the ceiling down?
Usually only part of the ceiling needs to come down. The boxing and a strip of ceiling either side of the beam are removed so props can go in and the old steel can come out. The rest of the room is protected, and the disturbed area is replastered to blend with the existing finish.
Why has my steel beam sagged?
A beam usually sags because it is too small for the load, the load has increased since it was fitted, or its bearings have crushed or moved. Every beam bends slightly within design limits, but a visible dip or new cracking suggests something has changed. An engineer can measure it and identify the cause.
What happens at the survey visit in Heavitree?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.