Load-bearing wall removal · Greenwich
Load-bearing wall removal in Greenwich
Steelwork, approvals and making good for load-bearing wall removal in Greenwich and nearby.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Greenwich and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our load-bearing wall removal service in Greenwich
Load-bearing wall removal in Greenwich is planned around the house, not a standard kit. We also cover the surrounding towns and villages in London. We visit, measure and check what the wall carries, then arrange calculations and building control approval before any steel is ordered.
Most homes built before the 1970s have at least one internal wall that carries the floor joists, a wall upstairs or part of the roof. Taking it out is very doable, but the weight it carries has to go somewhere. A steel beam picks that load up and passes it down through padstones into walls or columns that can take it.
Key points for your project
- Each end of the beam needs a solid bearing. Padstones spread the point load into the masonry below, and if the wall underneath is weak the engineer may call for a steel column or a new pad foundation instead.
- Whether a wall is load-bearing is not always obvious. Joists running across the wall, a wall directly above, or the wall sitting on a footing in the floor are common clues, but the engineer's check on site is what settles it.
- Temporary works matter as much as the beam. Props, spreaders and needles carry the house while the wall is out, and they are positioned so the floor below can take them too.
- The beam size depends on the span, what sits above and how the ends are supported. Two walls that look the same can need very different steel, which is why every beam is sized from calculations rather than guessed.
- The finished opening should be signed off with a completion certificate from building control. Keep it with your house documents, as solicitors ask for it when the property is sold.
How the job runs in Greenwich
Free visit
A short visit to Greenwich to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
What does load-bearing wall removal cost in Greenwich?
As a guide, budget £2,550–£6,400 including VAT for load-bearing wall removal with steel beam in Greenwich, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Load-bearing wall removal with steel beam | £2,550–£6,400 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Building control fees | £320–£830 | Building notice or full plans fee and inspections; varies by council or approver |
| Structural calculations for a beam | £320–£960 | Site measure or photos, beam and padstone design and calculations for building control |
| Kitchen-diner knock-through | £3,200–£7,700 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building rules for Greenwich
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Load-bearing wall removal near Greenwich
- Blackheath 1.2 mi
- Catford 2.3 mi
- Peckham 2.5 mi
- Canning Town 2.8 mi
- Eltham 3.3 mi
- Bow 3.3 mi
Load-bearing wall removal in Greenwich: your questions
Can I stay at home while the work is done in Greenwich?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
What happens at the survey visit in Greenwich?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
How do I know if my wall is load-bearing?
Clues include floor joists that run across the top of the wall, a wall directly above it upstairs, and a wall that is solid brick or block rather than a hollow stud partition. None of these is proof on its own. A structural engineer checks on site and confirms it before any work is planned.
What does the price include?
Our written quote is itemised, so you can see the calculations, building control fees, propping, steel, padstones, labour, fire protection and making good set out line by line. The price is fixed in writing once the layout and scope are agreed.
Do I need planning permission to remove an internal wall?
Usually not, because internal alterations to a house are not normally development needing planning permission. Listed buildings are different and need listed building consent, and flats normally need the freeholder's or landlord's written consent.
Can you work on older or listed homes in Greenwich?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.