Load-bearing wall removal · Eltham
Load-bearing wall removal in Eltham
Steelwork, approvals and making good for load-bearing wall removal in Eltham and nearby.
- Survey, design and installation in one
- Covering DA15, DA16, SE3
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What load-bearing wall removal involves in Eltham
Our load-bearing wall removal service in Eltham covers everything from the first visit to the completion paperwork. Our coverage runs across London, so nearby villages are included too. Postcode districts we cover here include DA15, DA16, SE3, SE7 and SE9.
We handle the whole job: a survey visit, structural calculations from a qualified engineer, building control, temporary propping, the steel itself, and making good afterwards. You get one itemised written quote and one team to deal with from first visit to sign-off.
What to expect
- Building control is needed because removing a structural wall is controlled building work. Doing it without approval can cause problems when you come to sell, and putting it right afterwards costs far more than doing it properly first time.
- Most single-wall removals in a typical house take two to five working days on site for the structural part. Plastering, drying out and decorating follow on, and building control visits fit around those stages.
- Steel beams in homes usually need fire protection. That is often fire-rated plasterboard boxing, which also gives a neat finish, or intumescent paint where the steel is left on show.
- A beam can sit below the ceiling with a small boxed downstand or be set up into the floor void so the ceiling runs flat. A flush beam usually needs more work to the joists and costs more.
- Cables, pipes, radiators and sometimes gas runs pass through internal walls. These are traced at the survey so they can be rerouted by the right trade before or during the work, not discovered halfway through.
How the job runs in Eltham
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
How much should I budget in Eltham?
As a guide, budget £2,550–£6,400 including VAT for load-bearing wall removal with steel beam in Eltham, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Load-bearing wall removal with steel beam | £2,550–£6,400 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Structural calculations for a beam | £320–£960 | Site measure or photos, beam and padstone design and calculations for building control |
| Building control fees | £320–£830 | Building notice or full plans fee and inspections; varies by council or approver |
| RSJ supply and fit (single beam) | £1,000–£3,200 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building control and neighbours in Eltham
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Load-bearing wall removal in Eltham: your questions
Can you work on older or listed homes in Eltham?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Can I stay in the house while the wall is removed?
In most cases yes. The work area is screened, floors are protected and the house stays usable, though the rooms either side of the wall will be out of action for a few days and there will be some noise and dust.
Who sizes the steel beam?
A structural engineer. They look at the span, the loads from floors, walls and roof above, and the bearings at each end, then specify the beam, padstones and any columns. We arrange those calculations, or work to calculations you already have.
What happens if the wall is shared with my neighbour?
In England and Wales, cutting into a party wall to take the end of a beam is covered by the Party Wall etc. Act 1996, and notice must be served on the neighbour before work starts. Scotland and Northern Ireland have no equivalent Act, so the title deeds and the general law apply instead.