Structural calculations · Greenwich
Structural calculations in Greenwich
Structural calculations for homes in E14, SE3, SE4, designed by a structural engineer.
- Free survey visit in Greenwich
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Structural calculations in Greenwich: how it works
For homes in Greenwich and the E14, SE3, SE4, SE7 and SE8 districts, we handle structural calculations from survey to sign-off. We also cover the surrounding towns and villages in London. The beam is sized by a structural engineer and inspected before it is boxed in.
Building control will not approve a beam on trust. Before steel goes in, someone has to show in writing what the beam is carrying, what size it needs to be and how its ends are supported. That is the job of structural calculations, prepared by a qualified structural engineer from measurements taken at the property.
Key points for your project
- Opening up can reveal things no survey could see, such as a hidden chimney flue, joists running the other way or a wall with no footing. When that happens, the engineer revises the design before work continues, and any change is priced before it goes ahead.
- A typical calculation pack covers the loads assumed, the beam section chosen, checks for bending, shear and deflection, the bearing and padstone design, and any column or foundation design. It is usually accompanied by a drawing or sketch showing positions.
- The cost of calculations rises with complexity: the number of beams and columns, whether loads come down from several floors, whether foundations need designing, and how much investigation is needed on site. A single straightforward beam sits at the simpler end.
- Building control uses the calculations to check compliance with Part A of the Building Regulations in England and Wales, or the equivalent structural standards in Scotland and Northern Ireland. Without them, an application for structural work is unlikely to be approved.
- Accurate site information is essential. The engineer needs real spans, joist directions, wall build-ups and what sits above, so a site visit or detailed survey usually comes before any calculations. Guesswork from estate agent floor plans is not enough.
What happens, step by step
Survey in Greenwich
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Greenwich?
As a guide, budget £320–£960 including VAT for structural calculations for a beam in Greenwich, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Structural calculations for a beam | £320–£960 | Site measure or photos, beam and padstone design and calculations for building control |
| Load-bearing wall removal with steel beam | £2,550–£6,400 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Temporary works and propping | £190–£640 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Loft conversion steels | £3,200–£7,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Approvals in Greenwich
For Greenwich, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Structural calculations near Greenwich
- Blackheath 1.2 mi
- Catford 2.3 mi
- Peckham 2.5 mi
- Canning Town 2.8 mi
- Eltham 3.3 mi
- Bow 3.3 mi
Structural calculations in Greenwich: your questions
Who approves structural calculations in Greenwich?
Structural work in Greenwich needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Can I stay at home while the work is done in Greenwich?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Can I use calculations from my architect or previous builder?
Yes, as long as they match what is actually being built. We check the spans, loads and bearing details against the layout and the site before ordering steel. If the plans have changed since the calculations were done, or the site differs from what was assumed, the engineer needs to update them first.
Do I need structural calculations to remove a wall?
Yes, if the wall is load-bearing. Building control needs calculations showing that the new beam, its bearings and anything supporting it can carry the loads safely. Non-structural stud partitions normally do not need them, but an engineer should confirm a wall is non-structural before anyone assumes it.
Does the engineer need to visit my house?
Usually, yes, or at least work from a detailed survey of the property. The engineer needs accurate spans, joist directions, wall construction and an understanding of what sits above the opening. Calculations based only on a floor plan or photos risk missing loads, which can lead to redesign once work starts.
Do you also work near Greenwich?
Yes. We also cover nearby towns including Blackheath, Catford, Peckham and Canning Town.