Loft conversion steels · Greenwich
Loft conversion steels in Greenwich
Steelwork, approvals and making good for loft conversion steels in Greenwich and nearby.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Greenwich and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our loft conversion steels service in Greenwich
We carry out loft conversion steels in Greenwich, covering the E14, SE3, SE4, SE7 and SE8 postcode districts. The wider London area is covered as well. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
The joists in most lofts were only ever meant to hold up a plaster ceiling, and the roof is often propped on struts and purlins that get in the way of a room. Steel beams solve both problems: they carry a new floor across the house and take over the roof support so the struts can come out.
What to expect
- Getting steel into a loft is often the hardest part of the job. Beams can be brought through a roof opening, a gable window, or in shorter lengths bolted together inside, provided the engineer's design allows for the splice.
- Headroom in the finished loft depends partly on where the floor steels sit. Setting them low, between the existing ceiling joists, keeps more height upstairs, and the engineer and loft designer agree the levels together.
- A rear dormer removes part of the roof slope, so the rafters above lose their support at the lower end. A ridge beam or a beam along the dormer's front edge carries them instead, designed for the dormer width and the weight of the roof.
- The steel stage of a loft conversion usually takes a few working days and comes early, before floor joists, dormer framing and insulation. Keep the steel calculations with the completion certificate, as both are asked for when the house is sold.
- Traditional cut roofs rely on purlins and struts running down to internal walls. A steel beam can take over that job so the struts come out, freeing up floor and headroom, but the change has to be designed and propped carefully.
From survey to sign-off in Greenwich
Survey in Greenwich
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for loft conversion steels in Greenwich
As a guide, budget £3,200–£7,700 including VAT for loft conversion steels in Greenwich, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £3,200–£7,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Temporary works and propping | £190–£640 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Fire protection to a steel beam | £190–£770 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| RSJ supply and fit (single beam) | £1,000–£3,200 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building control and neighbours in Greenwich
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Loft conversion steels near Greenwich
- Blackheath 1.2 mi
- Catford 2.3 mi
- Peckham 2.5 mi
- Canning Town 2.8 mi
- Eltham 3.3 mi
- Bow 3.3 mi
Loft conversion steels in Greenwich: your questions
Do you also work near Greenwich?
Yes. We also cover nearby towns including Blackheath, Catford, Peckham and Canning Town.
Who approves loft conversion steels in Greenwich?
Structural work in Greenwich needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Do all loft conversions need steel beams?
Most do, but not all. Steels are usually needed to carry the new floor, replace purlins and struts, or support the roof around a dormer. Some smaller conversions use deeper timber joists or engineered timber instead. A structural engineer decides what the roof and walls need after a survey.
Where do loft conversion steels sit?
Usually between the gable walls or party walls, bearing on padstones bedded into pockets cut in the brickwork. Floor beams sit low, close to the existing ceiling, while ridge or dormer beams sit higher up to support the roof. The engineer sets the exact positions and levels.
How long does it take to install loft steels?
The main steels for a typical loft conversion usually go in over two to five working days. That covers cutting pockets, bedding padstones, getting the steel in and packing it. The timing depends heavily on access and how many beams the design calls for.
Do I need a party wall agreement for loft conversion steels in Greenwich?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.