Plastering & making good · Sevenoaks
Plastering & making good in Sevenoaks
Plastering & making good for homes in TN13, TN14, designed by a structural engineer.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Sevenoaks and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Plastering & making good in Sevenoaks: how it works
Plastering & making good in Sevenoaks is planned around the house, not a standard kit. Sevenoaks is around 14.2 miles from Maidstone, and we cover both. We visit, measure and check what the wall carries, then arrange calculations and building control approval before any steel is ordered.
Structural work leaves a trail behind it: a steel beam to hide, ragged wall ends, a strip of missing floor, cracked ceiling where props stood and holes where needles passed through. However good the steel, this is the part you look at every day, so it deserves the same care as the structure.
Worth knowing before you start
- The cost depends mainly on the area to repair, the condition of the ceilings, whether period details need matching, and the size of the floor infill. Overboarding a badly damaged ceiling can work out more economical than patching it piece by piece.
- Hairline cracks sometimes appear along board joints or where new plaster meets old, as the building settles onto the steel and the plaster dries out. They are normal in the first months and are usually filled at the next redecoration.
- Fresh plaster has to dry before it is painted. A thin skim over board in a warm, ventilated room often dries within a few days to a week, while backing coats and deeper repairs take longer. Painting too soon can cause peeling and patchy colour.
- A boxed beam usually leaves a downstand below the ceiling line. Where a flat ceiling is wanted, the beam has to be set up into the floor void during installation, so the finish needs deciding before the steel goes in, not after.
- Period cornicing and ceiling roses can often be repaired or run to match the existing profile. Where a wall is removed between two rooms with cornice, the ends are usually returned neatly along the new beam so the detail looks intentional.
How the job runs in Sevenoaks
Free visit
A short visit to Sevenoaks to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
Guide prices for plastering & making good in Sevenoaks
As a guide, budget £340–£1,340 including VAT for plastering and making good in Sevenoaks, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £340–£1,340 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Load-bearing wall removal with steel beam | £2,250–£5,600 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Kitchen-diner knock-through | £2,800–£6,700 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| Chimney breast removal (ground floor) | £1,700–£3,350 | Ground-floor breast removed, steel to support the breast above, building control and making good |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building control and neighbours in Sevenoaks
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Plastering & making good in Sevenoaks: your questions
Who approves plastering & making good in Sevenoaks?
Structural work in Sevenoaks needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Can I stay at home while the work is done in Sevenoaks?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Can you match my old textured ceiling?
Often, yes, although a perfect match is hard over large patches. Before anything is touched, a textured coating applied before 2000 is tested for asbestos. Small areas can then be re-textured to blend in, while many people choose to skim the whole ceiling flat for a cleaner, consistent finish.
Is plastering included when a load-bearing wall is removed?
Yes, on our structural jobs making good is priced as part of the work and itemised on the written quote, so you can see exactly what is included. If another firm is doing the steelwork, check their quote closely, as some stop at the beam and leave plastering, floor infill and skirting for you to arrange.
Do you decorate after making good?
Not usually. Making good leaves surfaces skimmed, dry and ready for paint, with trims refitted, and decoration is normally left to you or your decorator so you can choose colours and finishes yourself. Whoever paints should start with a thinned mist coat on the new plaster before the main coats.
Do you also work near Sevenoaks?
Yes. We also cover nearby towns including Tonbridge, Swanley, Tunbridge Wells and Caterham.