Through-lounge knock-throughs · Sevenoaks
Through-lounge knock-throughs in Sevenoaks
Through-lounge knock-throughs for homes in TN13, TN14, designed by a structural engineer.
- Survey, design and installation in one
- Covering TN13, TN14
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning through-lounge knock-throughs in Sevenoaks
We carry out through-lounge knock-throughs in Sevenoaks, covering the TN13 and TN14 postcode districts. It sits about 14.2 miles from Maidstone, which we also cover. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
Many period terraces and semis were built with a front parlour and a back sitting room divided by a solid brick wall. Opening them into one through-lounge brings light from both ends of the house, but that wall commonly carries the floor joists, the wall between the bedrooms above and sometimes part of the roof load too.
Key points for your project
- The structural stage for a through-lounge typically takes three to five working days. Both reception rooms are out of use for that time, so furniture is moved out or stacked and sheeted, and the hallway is kept clear as the main walkway.
- Many owners leave short nibs of wall at each end of the opening rather than going fully wall to wall. Nibs can give the beam a bearing, line up with the chimney breasts and keep the feel of two linked rooms, but the engineer decides whether they are adequate.
- Victorian brickwork is usually laid in soft lime mortar and the internal walls may be only one brick thick. The engineer allows for this when designing the bearings, and padstones are often used to spread the beam's load over the weaker masonry.
- With the wall gone, the floorboards on each side may run in different directions or sit at slightly different heights. Matching reclaimed boards can be fitted across the old wall line, or the floor can be levelled for a new continuous finish.
- The steel commonly needs fire protection to meet building regulations, usually by boxing it in fire-rated plasterboard and skimming it. In period rooms the box can be finished with a matching cornice so it reads as part of the original ceiling.
How the job runs in Sevenoaks
Free visit
A short visit to Sevenoaks to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
What do through-lounge knock-throughs cost in Sevenoaks?
As a guide, budget £2,800–£6,150 including VAT for through-lounge knock-through in Sevenoaks, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Through-lounge knock-through | £2,800–£6,150 | Wall between front and back reception rooms, steel beam, approvals, plastering and floor infill |
| Chimney breast removal (ground floor) | £1,700–£3,350 | Ground-floor breast removed, steel to support the breast above, building control and making good |
| Kitchen-diner knock-through | £2,800–£6,700 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| Plastering and making good | £340–£1,340 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building control and neighbours in Sevenoaks
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Local questions answered
Do you cover Sevenoaks for through-lounge knock-throughs?
Yes. We carry out through-lounge knock-throughs in Sevenoaks and the TN13 and TN14 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
How soon can through-lounge knock-throughs start in Sevenoaks?
Start dates depend on the engineer's calculations, the building control approval and, where needed, party wall notice periods. We give you a realistic timetable after the survey and keep you updated as each approval comes through.
What happens to the floor where the wall was?
A strip of exposed joists, or a footing in a solid floor, is left where the wall stood. Timber floors are patched with matching or reclaimed boards, and solid floors are filled and levelled. If you are fitting a new floor across both rooms, it is simply prepared level for the new finish.
Do I need consent to knock through in a listed building?
Yes, you need both listed building consent and building regulations approval. Listed building consent from the local planning authority covers internal structural changes to the building's fabric, and building control covers the structural safety. Carrying out works to a listed building without consent is an offence, so it must be in place before anything is booked.
How wide can a through-lounge opening be?
That depends on what the wall carries and how the beam ends can be supported, and the structural engineer sets it. Many owners go nearly full width, keeping short nibs at each end, while others choose a narrower opening to keep two distinct rooms. Wider spans need heavier steel and sometimes columns.