Plastering & making good · Tonbridge
Plastering & making good in Tonbridge
Plastering & making good in Tonbridge, from free survey to completion certificate.
- Survey, design and installation in one
- Covering TN9, TN10, TN11
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning plastering & making good in Tonbridge
For homes in Tonbridge and the TN9, TN10 and TN11 districts, we handle plastering & making good from survey to sign-off. Tonbridge is around 11.6 miles from Maidstone, and we cover both. The beam is sized by a structural engineer and inspected before it is boxed in.
We make good as the final stage of our structural jobs, and can quote it separately where another firm has fitted the steel. It covers boxing and fire boarding, plastering and skimming, floor infills and skirting, leaving smooth, dry surfaces for your decorator.
Things to plan for
- Plastering itself is wet rather than dusty, but cutting back old plaster and sanding filler is not. Work areas are sheeted off, floors protected and dust extraction used when cutting, so the mess stays in the room being worked on.
- A boxed beam usually leaves a downstand below the ceiling line. Where a flat ceiling is wanted, the beam has to be set up into the floor void during installation, so the finish needs deciding before the steel goes in, not after.
- Victorian and Edwardian ceilings are often lath and lime plaster, which can sag or come away when nearby work shakes it. Small areas can be patched to match, while larger damaged areas are usually overboarded or replaced for a sound result.
- Making good is the last chance to route cables neatly before surfaces close up. Sockets, switches and lights moved for the new layout are first-fixed before boarding, and pipes crossing the old wall line can run within the floor infill.
- Metal angle beads on every outside corner of the boxing give crisp, straight lines and protect the edges from knocks. They are set true to the ceiling and walls, so a slightly out-of-level beam does not show once skimmed.
From survey to sign-off in Tonbridge
Survey in Tonbridge
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Tonbridge?
As a guide, budget £340–£1,340 including VAT for plastering and making good in Tonbridge, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £340–£1,340 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Kitchen-diner knock-through | £2,800–£6,700 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| Load-bearing wall removal with steel beam | £2,250–£5,600 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Chimney breast removal (ground floor) | £1,700–£3,350 | Ground-floor breast removed, steel to support the breast above, building control and making good |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Approvals in Tonbridge
For Tonbridge, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Plastering & making good near Tonbridge
- Tunbridge Wells 4.3 mi
- Sevenoaks 6.5 mi
- Crowborough 10.4 mi
- Maidstone 11.6 mi
- East Grinstead 13.1 mi
- Swanley 14.6 mi
Questions about plastering & making good in Tonbridge
Can you work on older or listed homes in Tonbridge?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Do you cover Tonbridge for plastering & making good?
Yes. We carry out plastering & making good in Tonbridge and the TN9, TN10 and TN11 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Do I need building control approval for plastering?
Not for plastering on its own. However, where it covers new structural steel, building control usually needs to inspect the beam and its fire protection before it is boxed in and skimmed. That is why, on structural jobs, the making good is timed around the building control visit.
Can you repair a lath and plaster ceiling?
Yes. Small areas can be patched with lath and lime-based plaster, or with board cut in and skimmed to match. Where large areas have sagged or pulled away from the laths, overboarding or replacing the ceiling is often the sounder repair. We assess the condition at the survey and price the right approach.
Do you replace skirting boards and door frames after a knock-through?
Yes, where the work affects them. Skirting is extended or replaced so it runs through the new opening, and door linings and architraves are refitted or replaced where an opening has changed. Where period mouldings are involved, matching profiles can usually be sourced or made up to suit.
What happens at the survey visit in Tonbridge?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.