Loft conversion steels · Tenby
Loft conversion steels in Tenby
Steelwork, approvals and making good for loft conversion steels in Tenby and nearby.
- Survey, design and installation in one
- Covering SA69, SA70
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What loft conversion steels involve in Tenby
Planning loft conversion steels in Tenby? Our team covers SA69 and SA70 and the streets around them. We also cover the surrounding towns and villages in Pembrokeshire. You get one written quote for the calculations, approvals, propping, steel and making good.
The joists in most lofts were only ever meant to hold up a plaster ceiling, and the roof is often propped on struts and purlins that get in the way of a room. Steel beams solve both problems: they carry a new floor across the house and take over the roof support so the struts can come out.
What to expect
- Loft steels usually bear on the gable wall in a semi-detached house or on the party wall in a terrace. The engineer checks that the wall below can take the point load and specifies padstones to spread it, sometimes with a steel post down to lower floors.
- Many later twentieth-century homes have trussed rafter roofs, with diagonal timbers running through the whole loft. Converting these involves more steel and new timber, because each truss is cut and its load has to be re-routed by design.
- Water tanks, cables, aerial leads and bathroom extract ducts often sit exactly where the steel needs to go. They are moved before the beams arrive, and old cold water tanks are frequently removed as part of the wider loft project.
- Traditional cut roofs rely on purlins and struts running down to internal walls. A steel beam can take over that job so the struts come out, freeing up floor and headroom, but the change has to be designed and propped carefully.
- In older terraces the party wall at loft level can be thin, built in soft brick, or contain old chimney flues. The engineer may avoid bearing over a flue, ask for a section of wall to be rebuilt, or use a post down to firmer support.
What happens, step by step
Survey in Tenby
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit the application or notice to Pembrokeshire County Council under the Building Regulations as they apply in Wales, before work starts.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Tenby?
As a guide, budget £2,300–£5,450 including VAT for loft conversion steels in Tenby, based on published UK cost guides adjusted for prices in Wales (-9%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £2,300–£5,450 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Temporary works and propping | £140–£460 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| RSJ supply and fit (single beam) | £730–£2,280 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Steel column or post | £460–£1,360 per column | Column supplied and fitted with base and cap plates on a pad foundation |
Figures include our approximate regional adjustment for prices in Wales (-9%) and are rounded. How these figures are worked out.
Building rules for Tenby
In Wales, structural alterations come under the Building Regulations 2010 as they apply in Wales. Pembrokeshire County Council handles building control for Tenby. For work started or approved from 1 July 2026, the Welsh system uses an application to building control, dutyholders appointed in writing, a commencement notice before work starts and a compliance statement at the end.
Where the steel bears into a wall shared with next door, notice must be served under the Party Wall etc. Act 1996. If your neighbour dissents, surveyors agree how the work is done before it starts.
Loft conversion steels near Tenby
- Pembroke 9.1 mi
- Pembroke Dock 10.5 mi
- Haverfordwest 14.5 mi
- Milford Haven 14.8 mi
- Burry Port 19.6 mi
- Carmarthen 21.2 mi
Local questions answered
How much do loft conversion steels cost in Tenby?
As a guide, budget £2,300–£5,450 including VAT for loft conversion steels in Tenby, based on published UK cost guides adjusted for prices in Wales (-9%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
Do I need a party wall agreement for loft conversion steels in Tenby?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
Can I stay in my house during a loft conversion?
Usually, yes. Most of the steel work happens in the roof space, with access through the loft hatch or a roof opening, so the rest of the house stays usable. Expect noise while pockets are cut into the walls and some dust on the landing, which is screened off.
How do you get steel beams into a loft?
It depends on access. Beams are often passed in through an opening made in the roof or a gable window, or brought up in shorter sections and bolted together in the loft where the engineer's design allows. For long or heavy steels a hoist or crane may be used, planned in advance.
Do loft conversion steels need fire protection?
Usually, yes. Steel loses strength in a fire, and the beams carrying the new floor are elements of structure. In a typical house they commonly need 30-minute fire resistance, often provided by fire-rated plasterboard around and below the steel, as agreed with building control.