Loft conversion steels · Hampshire
Loft conversion steels in Hampshire
Survey, engineer's design and installation of loft conversion steels anywhere in Hampshire.
- Free survey visit in Hampshire
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Loft conversion steels in Hampshire: how it works
Loft conversion steels are the beams that let a roof space become a usable room. They carry the new floor so it does not rest on the old ceiling joists, support the roof where purlins and struts are removed or rafters are cut for a dormer, and bear onto padstones in the gable or party walls as a structural engineer specifies.
If you are planning loft conversion steels in Hampshire, the order of work matters as much as the steel: survey, calculations, approval, propping, installation, inspection and making good. We can survey in places such as Farnborough, Eastleigh and Winchester and the villages around them. We run that sequence for you as one job with one point of contact.
Key points for your project
- Many later twentieth-century homes have trussed rafter roofs, with diagonal timbers running through the whole loft. Converting these involves more steel and new timber, because each truss is cut and its load has to be re-routed by design.
- A rear dormer removes part of the roof slope, so the rafters above lose their support at the lower end. A ridge beam or a beam along the dormer's front edge carries them instead, designed for the dormer width and the weight of the roof.
- Loft steels usually bear on the gable wall in a semi-detached house or on the party wall in a terrace. The engineer checks that the wall below can take the point load and specifies padstones to spread it, sometimes with a steel post down to lower floors.
- Steels supporting a loft floor commonly need 30-minute fire resistance in a typical house. That is usually achieved with fire-rated plasterboard below and around the steel, to the specification agreed with building control.
- Water tanks, cables, aerial leads and bathroom extract ducts often sit exactly where the steel needs to go. They are moved before the beams arrive, and old cold water tanks are frequently removed as part of the wider loft project.
Four stages, one team
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
What do loft conversion steels cost in Hampshire?
As a guide, budget £2,800–£6,700 including VAT for loft conversion steels in Hampshire, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £2,800–£6,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Structural calculations for a beam | £280–£840 | Site measure or photos, beam and padstone design and calculations for building control |
| RSJ supply and fit (single beam) | £900–£2,800 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Temporary works and propping | £170–£560 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building control and neighbours in Hampshire
For Hampshire, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Local questions answered
Can I stay at home while the work is done in Hampshire?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Do you cover Hampshire for loft conversion steels?
Yes. We carry out loft conversion steels in Hampshire. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Do all loft conversions need steel beams?
Most do, but not all. Steels are usually needed to carry the new floor, replace purlins and struts, or support the roof around a dormer. Some smaller conversions use deeper timber joists or engineered timber instead. A structural engineer decides what the roof and walls need after a survey.
Can my loft be converted if it has trussed rafters?
Often it can, but it is a bigger structural job. Trussed rafters have diagonal webs right through the loft, and every truss that is cut needs its load picked up by new steel and timber. The engineer designs that, and the roof is propped carefully throughout.
How long does it take to install loft steels?
The main steels for a typical loft conversion usually go in over two to five working days. That covers cutting pockets, bedding padstones, getting the steel in and packing it. The timing depends heavily on access and how many beams the design calls for.
Do I need a party wall notice for a loft conversion?
Very often in England and Wales, because loft steels in terraced and semi-detached houses usually bear into the party wall. That is notifiable under the Party Wall etc. Act 1996, with notice served at least two months before the work starts. We organise this through a party wall surveyor as part of the job.
What happens at the survey visit in Hampshire?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.