Loft conversion steels · Winchester
Loft conversion steels in Winchester
Loft conversion steels in Winchester, from free survey to completion certificate.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What loft conversion steels involve in Winchester
Loft conversion steels in Winchester are planned around the house, not a standard kit. Winchester is around 11.7 miles from Southampton, and we cover both. We visit, measure and check what the wall carries, then arrange calculations and building control approval before any steel is ordered.
The joists in most lofts were only ever meant to hold up a plaster ceiling, and the roof is often propped on struts and purlins that get in the way of a room. Steel beams solve both problems: they carry a new floor across the house and take over the roof support so the struts can come out.
Things to plan for
- Cutting pockets into a party wall for steel bearings is notifiable work in England and Wales under the Party Wall etc. Act 1996. A party structure notice must be served at least two months before that work starts, so it is worth raising early in the planning.
- A rear dormer removes part of the roof slope, so the rafters above lose their support at the lower end. A ridge beam or a beam along the dormer's front edge carries them instead, designed for the dormer width and the weight of the roof.
- Many loft conversions in houses in England fall within permitted development. Roof extensions facing a road, work in conservation areas, listed buildings and flats generally need planning permission or another form of consent.
- Traditional cut roofs rely on purlins and struts running down to internal walls. A steel beam can take over that job so the struts come out, freeing up floor and headroom, but the change has to be designed and propped carefully.
- Steels supporting a loft floor commonly need 30-minute fire resistance in a typical house. That is usually achieved with fire-rated plasterboard below and around the steel, to the specification agreed with building control.
From survey to sign-off in Winchester
Free visit
A short visit to Winchester to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
Guide prices for loft conversion steels in Winchester
As a guide, budget £2,800–£6,700 including VAT for loft conversion steels in Winchester, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £2,800–£6,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Steel column or post | £560–£1,680 per column | Column supplied and fitted with base and cap plates on a pad foundation |
| RSJ supply and fit (single beam) | £900–£2,800 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Fire protection to a steel beam | £170–£670 per beam | Fire-rated board boxing or an intumescent coating system as specified |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Winchester
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Questions about loft conversion steels in Winchester
Can I stay at home while the work is done in Winchester?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
What happens at the survey visit in Winchester?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
How long does it take to install loft steels?
The main steels for a typical loft conversion usually go in over two to five working days. That covers cutting pockets, bedding padstones, getting the steel in and packing it. The timing depends heavily on access and how many beams the design calls for.
What is a ridge beam in a loft conversion?
A ridge beam is a steel beam running along the top of the roof to support the rafters when their usual support is removed, such as when a large dormer is built or a hipped roof is converted to a gable. The engineer decides whether one is needed and specifies it.
Do loft conversion steels need fire protection?
Usually, yes. Steel loses strength in a fire, and the beams carrying the new floor are elements of structure. In a typical house they commonly need 30-minute fire resistance, often provided by fire-rated plasterboard around and below the steel, as agreed with building control.