Loft conversion steels · Bordon
Loft conversion steels in Bordon
Steelwork, approvals and making good for loft conversion steels in Bordon and nearby.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Bordon and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Loft conversion steels in Bordon: how it works
We cover loft conversion steels in Bordon (GU35) and the streets around it. Bordon is around 14.2 miles from Basingstoke, and we cover both. Each job is designed by a structural engineer and approved through local building control before work begins.
The joists in most lofts were only ever meant to hold up a plaster ceiling, and the roof is often propped on struts and purlins that get in the way of a room. Steel beams solve both problems: they carry a new floor across the house and take over the roof support so the struts can come out.
Key points for your project
- Steels supporting a loft floor commonly need 30-minute fire resistance in a typical house. That is usually achieved with fire-rated plasterboard below and around the steel, to the specification agreed with building control.
- In older terraces the party wall at loft level can be thin, built in soft brick, or contain old chimney flues. The engineer may avoid bearing over a flue, ask for a section of wall to be rebuilt, or use a post down to firmer support.
- Water tanks, cables, aerial leads and bathroom extract ducts often sit exactly where the steel needs to go. They are moved before the beams arrive, and old cold water tanks are frequently removed as part of the wider loft project.
- Loft steels usually bear on the gable wall in a semi-detached house or on the party wall in a terrace. The engineer checks that the wall below can take the point load and specifies padstones to spread it, sometimes with a steel post down to lower floors.
- Ceiling joists in most houses are too shallow to carry people, furniture and a bathroom. Rather than loading them, steel beams span between the walls and new, deeper floor joists hang from them, sitting just above the old ceiling.
From survey to sign-off in Bordon
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
What do loft conversion steels cost in Bordon?
As a guide, budget £2,800–£6,700 including VAT for loft conversion steels in Bordon, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £2,800–£6,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| RSJ supply and fit (single beam) | £900–£2,800 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Fire protection to a steel beam | £170–£670 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Temporary works and propping | £170–£560 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Bordon
For Bordon, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Loft conversion steels near Bordon
- Farnham 7.5 mi
- Aldershot 10.2 mi
- Fleet 11.8 mi
- Godalming 11.8 mi
- Farnborough 13.3 mi
- Basingstoke 14.2 mi
Questions about loft conversion steels in Bordon
How soon can loft conversion steels start in Bordon?
Start dates depend on the engineer's calculations, the building control approval and, where needed, party wall notice periods. We give you a realistic timetable after the survey and keep you updated as each approval comes through.
Do I need a party wall agreement for loft conversion steels in Bordon?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
How do you get steel beams into a loft?
It depends on access. Beams are often passed in through an opening made in the roof or a gable window, or brought up in shorter sections and bolted together in the loft where the engineer's design allows. For long or heavy steels a hoist or crane may be used, planned in advance.
What is a ridge beam in a loft conversion?
A ridge beam is a steel beam running along the top of the roof to support the rafters when their usual support is removed, such as when a large dormer is built or a hipped roof is converted to a gable. The engineer decides whether one is needed and specifies it.
Can I stay in my house during a loft conversion?
Usually, yes. Most of the steel work happens in the roof space, with access through the loft hatch or a roof opening, so the rest of the house stays usable. Expect noise while pockets are cut into the walls and some dust on the landing, which is screened off.
Can you work on older or listed homes in Bordon?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.