Structural calculations · Hampshire
Structural calculations in Hampshire
Structural calculations across Hampshire, designed by a structural engineer and signed off by building control.
- Free survey visit in Hampshire
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our structural calculations service in Hampshire
Structural calculations are an engineer's written design showing that a beam, column or other structural element can safely carry the loads placed on it. For steel beam work they set out the loads from floors, walls and roof, the steel section, the padstones or columns at each end and any propping requirements, and they are submitted to building control.
From the first survey visit to the completion certificate, we take care of structural calculations across Hampshire. Coverage takes in Fareham, Farnborough and Gosport and everywhere in between. The engineer sizes the steel, we deal with building control, and our team fits and packs the beam before making good.
Worth knowing before you start
- Calculations can also cover how the structure is held up during the work. For straightforward openings this may be a note on prop positions, while larger or more complex jobs may need a separate temporary works design.
- If you already have calculations from your own engineer or architect, we can work to them, provided they match the layout being built. We check that the spans, loads and bearings shown agree with what is on site before ordering steel.
- The beam ends are designed as carefully as the beam. Calculations check that the masonry under each end can take the concentrated load, and specify a padstone, spreader or column where it cannot. Weak brickwork beneath a bearing is a common reason for design changes.
- A typical calculation pack covers the loads assumed, the beam section chosen, checks for bending, shear and deflection, the bearing and padstone design, and any column or foundation design. It is usually accompanied by a drawing or sketch showing positions.
- How long calculations take depends on the engineer's workload and how complicated the job is. A single beam is quicker to design than a loft conversion with several steels, and any opening up needed for investigation adds time before figures can be issued.
How the job runs in Hampshire
Free visit
A short visit to Hampshire to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
What do structural calculations cost in Hampshire?
As a guide, budget £280–£840 including VAT for structural calculations for a beam in Hampshire, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Structural calculations for a beam | £280–£840 | Site measure or photos, beam and padstone design and calculations for building control |
| RSJ supply and fit (single beam) | £900–£2,800 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Building control fees | £280–£730 | Building notice or full plans fee and inspections; varies by council or approver |
| Steel beam replacement | £2,250–£6,150 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Approvals in Hampshire
For Hampshire, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Structural calculations in Hampshire: your questions
Which towns in Hampshire do you cover?
We cover towns including Southampton, Portsmouth, Basingstoke and Gosport, plus the villages and smaller towns around them.
Can I stay at home while the work is done in Hampshire?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
What happens if building control questions the calculations?
The engineer answers the query, usually by providing extra checks, clarifying an assumption or adjusting the design. This is a normal part of the approval process and does not mean anything is wrong. Work on the affected element waits until building control is satisfied, and any design change that affects cost is priced before it goes ahead.
What is a load take-down?
A load take-down is the part of the calculations that adds up every load reaching a beam or column and follows it down to the ground. It includes the roof, floors, walls, people, furniture and, where relevant, snow and wind. Each element along that path is then checked to make sure it can carry its share.
Can I use calculations from my architect or previous builder?
Yes, as long as they match what is actually being built. We check the spans, loads and bearing details against the layout and the site before ordering steel. If the plans have changed since the calculations were done, or the site differs from what was assumed, the engineer needs to update them first.
Does the engineer need to visit my house?
Usually, yes, or at least work from a detailed survey of the property. The engineer needs accurate spans, joist directions, wall construction and an understanding of what sits above the opening. Calculations based only on a floor plan or photos risk missing loads, which can lead to redesign once work starts.