Structural calculations · Caldicot
Structural calculations in Caldicot
Structural calculations in Caldicot, from free survey to completion certificate.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Caldicot and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What structural calculations involve in Caldicot
Structural calculations in Caldicot are planned around the house, not a standard kit. The wider Monmouthshire area is covered as well. We visit, measure and check what the wall carries, then arrange calculations and building control approval before any steel is ordered.
We arrange the calculations as part of every structural job, or work to calculations you already have if they match the design. The engineer's output goes to building control with the application, and the same figures guide the steel order, the padstones and the propping on site.
Worth knowing before you start
- Opening up can reveal things no survey could see, such as a hidden chimney flue, joists running the other way or a wall with no footing. When that happens, the engineer revises the design before work continues, and any change is priced before it goes ahead.
- The beam ends are designed as carefully as the beam. Calculations check that the masonry under each end can take the concentrated load, and specify a padstone, spreader or column where it cannot. Weak brickwork beneath a bearing is a common reason for design changes.
- How long calculations take depends on the engineer's workload and how complicated the job is. A single beam is quicker to design than a loft conversion with several steels, and any opening up needed for investigation adds time before figures can be issued.
- The cost of calculations rises with complexity: the number of beams and columns, whether loads come down from several floors, whether foundations need designing, and how much investigation is needed on site. A single straightforward beam sits at the simpler end.
- The calculations or the building control approval usually state the fire resistance the steel needs, commonly 30 minutes in typical houses. That requirement then decides whether the beam is boxed in fire-rated plasterboard, painted with intumescent coating or protected another way.
How the job runs in Caldicot
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit the application or notice to Monmouthshire County Council under the Building Regulations as they apply in Wales, before work starts.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
Guide prices for structural calculations in Caldicot
As a guide, budget £230–£680 including VAT for structural calculations for a beam in Caldicot, based on published UK cost guides adjusted for prices in Wales (-9%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Structural calculations for a beam | £230–£680 | Site measure or photos, beam and padstone design and calculations for building control |
| RSJ supply and fit (single beam) | £730–£2,280 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Steel beam replacement | £1,800–£5,000 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Temporary works and propping | £140–£460 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in Wales (-9%) and are rounded. How these figures are worked out.
Building control and neighbours in Caldicot
In Wales, structural alterations come under the Building Regulations 2010 as they apply in Wales. Monmouthshire County Council handles building control for Caldicot. For work started or approved from 1 July 2026, the Welsh system uses an application to building control, dutyholders appointed in writing, a commencement notice before work starts and a compliance statement at the end.
The Party Wall etc. Act 1996 applies in Wales as well as England, so a beam bearing into a shared wall needs a party structure notice at least two months before work starts. We arrange notices through a party wall surveyor.
Questions about structural calculations in Caldicot
Do I need a party wall agreement for structural calculations in Caldicot?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
Do you cover Caldicot for structural calculations?
Yes. We carry out structural calculations in Caldicot and the NP26 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Do I need structural calculations to remove a wall?
Yes, if the wall is load-bearing. Building control needs calculations showing that the new beam, its bearings and anything supporting it can carry the loads safely. Non-structural stud partitions normally do not need them, but an engineer should confirm a wall is non-structural before anyone assumes it.
What do structural calculations for a steel beam include?
They include the loads the beam carries, the steel section chosen, checks for bending, shear and deflection, and the design of the padstones or columns at each end. Most packs also come with a drawing or sketch showing positions and bearing details, and note the fire protection and any propping requirements.
Do structural calculations tell you which beam to buy?
Yes. The calculations specify the steel section, its grade and length, and the padstones or columns it needs, so the fabricator can supply exactly what was designed. Substituting a different beam on site without the engineer's agreement would leave the work out of line with the approved design.
Who approves structural calculations in Caldicot?
Structural work in Caldicot needs a building control application to Monmouthshire County Council under the Welsh regulations, with a commencement notice before work starts. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.