Structural calculations · Devon
Structural calculations in Devon
Survey, engineer's design and installation of structural calculations anywhere in Devon.
- Free survey visit in Devon
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our structural calculations service in Devon
Structural calculations are an engineer's written design showing that a beam, column or other structural element can safely carry the loads placed on it. For steel beam work they set out the loads from floors, walls and roof, the steel section, the padstones or columns at each end and any propping requirements, and they are submitted to building control.
We carry out structural calculations throughout Devon, for homeowners, landlords and builders who need the structural part done properly. We work in Exmouth, Paignton and Newton Abbot and the surrounding villages. You get an itemised written quote that shows the calculations, approvals, steel, labour and finishing as separate lines.
Things to plan for
- If you already have calculations from your own engineer or architect, we can work to them, provided they match the layout being built. We check that the spans, loads and bearings shown agree with what is on site before ordering steel.
- How long calculations take depends on the engineer's workload and how complicated the job is. A single beam is quicker to design than a loft conversion with several steels, and any opening up needed for investigation adds time before figures can be issued.
- Strength is only half the design. The engineer also limits how much the beam bends under load, because excessive deflection cracks plaster, jams doors and can damage glazing. Wide glazed openings often need a stiffer beam than strength alone would suggest.
- A typical calculation pack covers the loads assumed, the beam section chosen, checks for bending, shear and deflection, the bearing and padstone design, and any column or foundation design. It is usually accompanied by a drawing or sketch showing positions.
- The calculations or the building control approval usually state the fire resistance the steel needs, commonly 30 minutes in typical houses. That requirement then decides whether the beam is boxed in fire-rated plasterboard, painted with intumescent coating or protected another way.
Four stages, one team
Free visit
A short visit to Devon to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
How much should I budget in Devon?
As a guide, budget £260–£770 including VAT for structural calculations for a beam in Devon, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Structural calculations for a beam | £260–£770 | Site measure or photos, beam and padstone design and calculations for building control |
| Steel beam replacement | £2,050–£5,650 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Loft conversion steels | £2,600–£6,200 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Building control fees | £260–£670 | Building notice or full plans fee and inspections; varies by council or approver |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Building control and neighbours in Devon
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Structural calculations in Devon: your questions
Can you work on older or listed homes in Devon?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Which towns in Devon do you cover?
We cover towns including Plymouth, Exeter, Paignton and Torquay, plus the villages and smaller towns around them.
How long do structural calculations take?
It varies with the engineer's workload and the complexity of the design, so there is no fixed turnaround. A single beam in a straightforward wall is usually quicker than a loft conversion or a frame with foundations. Any site investigation needed first, and any building control queries afterwards, add to the overall time.
What happens if building control questions the calculations?
The engineer answers the query, usually by providing extra checks, clarifying an assumption or adjusting the design. This is a normal part of the approval process and does not mean anything is wrong. Work on the affected element waits until building control is satisfied, and any design change that affects cost is priced before it goes ahead.
Do I need structural calculations to remove a wall?
Yes, if the wall is load-bearing. Building control needs calculations showing that the new beam, its bearings and anything supporting it can carry the loads safely. Non-structural stud partitions normally do not need them, but an engineer should confirm a wall is non-structural before anyone assumes it.
Can a builder size a steel beam without an engineer?
Not for building control purposes. Building control normally expects calculations from a qualified structural engineer showing the beam is adequate for the actual loads. Rules of thumb do not account for what sits above or how the ends are supported, which is why we always work from an engineer's design.