Steel beam replacement & repair · Wallington
Steel beam replacement & repair in Wallington
Steelwork, approvals and making good for steel beam replacement & repair in Wallington and nearby.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What steel beam replacement & repair involves in Wallington
Planning steel beam replacement & repair in Wallington? Our team covers CR4, CR8, SM1, SM2 and SM3 and the streets around them. We also cover the surrounding towns and villages in London. You get one written quote for the calculations, approvals, propping, steel and making good.
We start with a survey visit, arrange an engineer's inspection, then carry out whatever repair the engineer specifies, from new bearings to strengthening or full replacement. We handle building control and the temporary propping, and you get an itemised written quote before anything starts.
Things to plan for
- Whether to strengthen or replace is the engineer's decision. Plating, where steel plates are fixed to the flanges, can add capacity without removing the beam, but it is not suitable for every section, connection or level of damage.
- Shop beams over old shopfronts are a common repair job. They often carry the whole front wall of the upper floors, sit behind fascias where rain gets in, and may have been cut or altered when shopfronts were replaced in the past.
- Beams fitted without calculations, whether decades ago or more recently without approval, may be smaller than the loads require, particularly in shop conversions and older knock-throughs. An engineer can check the existing section against the actual loads and say whether it is adequate.
- A repair only lasts if the cause is dealt with too. A leaking roof, blocked gutter or bridged damp-proof course that rusted the beam needs fixing first, otherwise new protective coatings will break down in the same way.
- Replacing a beam that is already carrying load is more delicate than fitting a new one. Props go in on both sides before anything is cut, with spreaders above and below, and the old steel is often cut into sections to lift it out safely.
From survey to sign-off in Wallington
Free visit
A short visit to Wallington to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
What does steel beam replacement & repair cost in Wallington?
As a guide, budget £2,550–£7,050 including VAT for steel beam replacement in Wallington, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steel beam replacement | £2,550–£7,050 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Temporary works and propping | £190–£640 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Fire protection to a steel beam | £190–£770 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Building control fees | £320–£830 | Building notice or full plans fee and inspections; varies by council or approver |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Approvals in Wallington
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Steel beam replacement & repair near Wallington
- Carshalton 0.7 mi
- Sutton 2.2 mi
- South Croydon 2.6 mi
- Purley 2.6 mi
- Croydon 2.7 mi
- Mitcham 2.8 mi
Steel beam replacement & repair in Wallington: your questions
What happens at the survey visit in Wallington?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Can I stay at home while the work is done in Wallington?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Can an old shop beam be replaced while the flat above is occupied?
Often, yes, with careful planning. The front wall and floors above are propped from inside the shop, and sometimes from outside, before the old beam is cut out. Occupants can often stay in if the engineer is satisfied with the propping, though there will be noise for a few days. Where the flat is separately owned, access and consents need agreeing in advance.
Do I need building control to replace a steel beam?
Yes, replacing or strengthening a structural beam is building work. In England and Wales it needs building regulations approval, in Scotland a building warrant before work starts, and in Northern Ireland an application to council building control. Simple redecoration or treating light surface rust without altering the structure does not normally need approval.
Can you replace a steel beam without taking the ceiling down?
Usually only part of the ceiling needs to come down. The boxing and a strip of ceiling either side of the beam are removed so props can go in and the old steel can come out. The rest of the room is protected, and the disturbed area is replastered to blend with the existing finish.