Side return extension steels · Chorley
Side return extension steels in Chorley
Side return extension steels in Chorley, from free survey to completion certificate.
- Survey, design and installation in one
- Covering PR6, PR7
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Side return extension steels in Chorley: how it works
We cover side return extension steels in Chorley (PR6, PR7) and the streets around it. Chorley is around 7.4 miles from Wigan, and we cover both. Each job is designed by a structural engineer and approved through local building control before work begins.
Many Victorian and Edwardian terraces have a narrow back wing, often called an outrigger, with a strip of yard down one side. Infilling that strip turns a galley kitchen into a wide family room, but the outrigger's side wall usually holds up a bathroom or bedroom above, so it has to be replaced with steel.
Things to plan for
- Glazed roofs over side returns are usually made to measure and need an edge that stays straight and level. The engineer may set a stiffer limit on how far the steel can deflect so the glazing is not stressed once loaded.
- The side wall of a typical outrigger carries the first-floor wall above it, and sometimes the rear wing's roof and the joists of the room over the kitchen. That is why taking it out calls for a beam along its full length.
- Many outrigger kitchens have a chimney breast on the side wall being removed or on the party wall. Its position affects where beams can bear, and if any part of the breast is taken out, what remains above has to be supported as the engineer specifies.
- Victorian outrigger walls are often a single brick thick in soft lime mortar, sometimes on very shallow footings. The engineer may ask for trial holes before deciding whether new foundations are needed under the column positions or beam ends.
- Side passages often carry the house drains and rainwater pipes from the outrigger roof. Manholes and pipe runs are located early, and a shared or public sewer under the passage may need the water company's agreement before building over or near it.
What happens, step by step
Survey in Chorley
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Chorley?
As a guide, budget £3,350–£8,150 including VAT for side return extension steelwork in Chorley, based on published UK cost guides adjusted for prices in the North West (-4%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Side return extension steelwork | £3,350–£8,150 | Beams and posts along the old side wall line, propping and approvals (extension build extra) |
| Structural calculations for a beam | £240–£720 | Site measure or photos, beam and padstone design and calculations for building control |
| Steel column or post | £480–£1,440 per column | Column supplied and fitted with base and cap plates on a pad foundation |
| Opening into a rear extension | £2,400–£6,700 | Original rear wall removed with a beam or goalpost, approvals and propping, coordinated with the extension build |
Figures include our approximate regional adjustment for prices in the North West (-4%) and are rounded. How these figures are worked out.
Building control and neighbours in Chorley
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Side return extension steels in Chorley: your questions
Who approves side return extension steels in Chorley?
Structural work in Chorley needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Do you also work near Chorley?
Yes. We also cover nearby towns including Leyland, Darwen, Wigan and Westhoughton.
How long does it take to fit side return steels?
Most side return steel frames take two to five working days on site, depending on the number of beams and columns and how easy access is. That covers propping, removing the old side wall, fitting the steels and packing them. Fire protection and finishes follow afterwards.
Do I need a party wall agreement for a side return extension?
In England and Wales it is very likely. Building on or near the boundary, excavating close to the neighbour's foundations or cutting into a shared wall can all be notifiable under the Party Wall etc. Act 1996. Notices are arranged through a party wall surveyor on your behalf, and we do not give legal advice.
Why does a side return need columns?
Columns are used where two beams meet or where there is not enough solid wall to carry the end of a beam. The column takes the concentrated load down to a pad foundation in the ground. Sometimes it can be hidden in a wall nib or boxed in neatly.