Plastering & making good · Telford
Plastering & making good in Telford
Steelwork, approvals and making good for plastering & making good in Telford and nearby.
- Survey, design and installation in one
- Covering TF1, TF2, TF3
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Plastering & making good in Telford: how it works
Need plastering & making good in Telford? The wider Shropshire area is covered as well. We survey the property, arrange the engineer's design, deal with Telford & Wrekin Council, fit the steel and make good, all under one quote for TF1, TF2, TF3, TF4 and TF7 addresses.
Structural work leaves a trail behind it: a steel beam to hide, ragged wall ends, a strip of missing floor, cracked ceiling where props stood and holes where needles passed through. However good the steel, this is the part you look at every day, so it deserves the same care as the structure.
Things to plan for
- Fresh plaster has to dry before it is painted. A thin skim over board in a warm, ventilated room often dries within a few days to a week, while backing coats and deeper repairs take longer. Painting too soon can cause peeling and patchy colour.
- When a wall is removed, a strip of floor goes with it. On suspended timber floors the gap is joisted and boarded, and on solid floors it is filled and screeded. Either way, the infill must sit level so new flooring does not show a ridge.
- A boxed beam usually leaves a downstand below the ceiling line. Where a flat ceiling is wanted, the beam has to be set up into the floor void during installation, so the finish needs deciding before the steel goes in, not after.
- Metal angle beads on every outside corner of the boxing give crisp, straight lines and protect the edges from knocks. They are set true to the ceiling and walls, so a slightly out-of-level beam does not show once skimmed.
- New plaster is very absorbent, so the first coat of emulsion is normally thinned with water as a mist coat to seal it. Skipping this step is a frequent reason paint flakes off fresh plaster within weeks of decorating.
What happens, step by step
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to Telford & Wrekin Council, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
What does plastering & making good cost in Telford?
As a guide, budget £300–£1,200 including VAT for plastering and making good in Telford, based on published UK cost guides adjusted for prices in the West Midlands (no adjustment).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £300–£1,200 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Load-bearing wall removal with steel beam | £2,000–£5,000 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Fire protection to a steel beam | £150–£600 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Through-lounge knock-through | £2,500–£5,500 | Wall between front and back reception rooms, steel beam, approvals, plastering and floor infill |
Figures include our approximate regional adjustment for prices in the West Midlands (no adjustment) and are rounded. How these figures are worked out.
Building rules for Telford
Structural openings in English homes need building regulations approval before work starts. Telford & Wrekin Council can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Plastering & making good near Telford
- Wellington 3.3 mi
- Shrewsbury 12.9 mi
- Wolverhampton 15.1 mi
- Wednesfield 16.2 mi
- Stafford 16.5 mi
- Kingswinford 17.1 mi
Plastering & making good in Telford: your questions
Can you work on older or listed homes in Telford?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
How much does plastering & making good cost in Telford?
As a guide, budget £300–£1,200 including VAT for plastering and making good in Telford, based on published UK cost guides adjusted for prices in the West Midlands (no adjustment). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
Do I need building control approval for plastering?
Not for plastering on its own. However, where it covers new structural steel, building control usually needs to inspect the beam and its fire protection before it is boxed in and skimmed. That is why, on structural jobs, the making good is timed around the building control visit.
What happens to the floor where the wall was removed?
The gap left by the wall is filled to match the floor on either side. Suspended timber floors get new joists and boards, solid floors are filled and screeded, and the infill is levelled so carpet, laminate or tiles can run straight across the room without a visible ridge.
How do you hide a steel beam in the ceiling?
Most beams are boxed with fire-rated plasterboard fixed to a light frame, then finished with corner beads and a skim coat so they read as part of the ceiling. If you want no downstand at all, the beam has to be set into the floor void when it is installed, which is decided at the design stage.
Do you cover Telford for plastering & making good?
Yes. We carry out plastering & making good in Telford and the TF1, TF2, TF3, TF4 and TF7 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.