Plastering & making good · Shropshire
Plastering & making good in Shropshire
Calculations, approvals, propping, steel and making good for plastering & making good across Shropshire.
- Free survey visit in Shropshire
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning plastering & making good in Shropshire
Plastering and making good is the finishing work after a beam goes in or a wall comes out: boxing the steel, fixing corner beads, patching ceilings and wall ends, infilling the floor where the wall stood and skimming everything smooth. The aim is a room that looks as if the opening was always there, ready for paint.
Homes across Shropshire range from Victorian terraces to post-war semis and newer estates, and plastering & making good looks different in each. We can survey in places such as Loughton, Wellington and Shrewsbury and the villages around them. We plan the steel, the temporary support and the approvals around the building, then fix the price in writing once the scope is agreed.
What to expect
- The cost depends mainly on the area to repair, the condition of the ceilings, whether period details need matching, and the size of the floor infill. Overboarding a badly damaged ceiling can work out more economical than patching it piece by piece.
- Textured ceiling coatings applied before 2000 can contain asbestos. Before a textured ceiling is cut, scraped or sanded, a sample is tested or an asbestos survey of the area is arranged, and the finish is only disturbed once the result is known.
- When a wall is removed, a strip of floor goes with it. On suspended timber floors the gap is joisted and boarded, and on solid floors it is filled and screeded. Either way, the infill must sit level so new flooring does not show a ridge.
- Making good is the last chance to route cables neatly before surfaces close up. Sockets, switches and lights moved for the new layout are first-fixed before boarding, and pipes crossing the old wall line can run within the floor infill.
- Metal angle beads on every outside corner of the boxing give crisp, straight lines and protect the edges from knocks. They are set true to the ceiling and walls, so a slightly out-of-level beam does not show once skimmed.
From survey to sign-off in Shropshire
Survey in Shropshire
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for plastering & making good in Shropshire
As a guide, budget £300–£1,200 including VAT for plastering and making good in Shropshire, based on published UK cost guides adjusted for prices in the West Midlands (no adjustment).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £300–£1,200 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Kitchen-diner knock-through | £2,500–£6,000 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| Load-bearing wall removal with steel beam | £2,000–£5,000 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Fire protection to a steel beam | £150–£600 per beam | Fire-rated board boxing or an intumescent coating system as specified |
Figures include our approximate regional adjustment for prices in the West Midlands (no adjustment) and are rounded. How these figures are worked out.
Building control and neighbours in Shropshire
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Plastering & making good by town
Local questions answered
Can you work on older or listed homes in Shropshire?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
How soon can plastering & making good start in Shropshire?
Start dates depend on the engineer's calculations, the building control approval and, where needed, party wall notice periods. We give you a realistic timetable after the survey and keep you updated as each approval comes through.
What happens to the floor where the wall was removed?
The gap left by the wall is filled to match the floor on either side. Suspended timber floors get new joists and boards, solid floors are filled and screeded, and the infill is levelled so carpet, laminate or tiles can run straight across the room without a visible ridge.
Will cracks appear after plastering?
Small hairline cracks can appear in the first months as the plaster dries and the building settles onto the new steel. They are cosmetic and normal, and are usually filled when you next repaint. Wide or growing cracks are different and should be reported, as they can point to movement that needs checking.
Do you decorate after making good?
Not usually. Making good leaves surfaces skimmed, dry and ready for paint, with trims refitted, and decoration is normally left to you or your decorator so you can choose colours and finishes yourself. Whoever paints should start with a thinned mist coat on the new plaster before the main coats.
How do you hide a steel beam in the ceiling?
Most beams are boxed with fire-rated plasterboard fixed to a light frame, then finished with corner beads and a skim coat so they read as part of the ceiling. If you want no downstand at all, the beam has to be set into the floor void when it is installed, which is decided at the design stage.
What happens at the survey visit in Shropshire?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.