Plastering & making good · Richmond
Plastering & making good in Richmond
Plastering & making good for homes in SW14, TW1, TW2, designed by a structural engineer.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What plastering & making good involves in Richmond
Our plastering & making good service in Richmond covers everything from the first visit to the completion paperwork. Our coverage runs across London, so nearby villages are included too. Postcode districts we cover here include SW14, TW1, TW2, TW3 and TW7.
Structural work leaves a trail behind it: a steel beam to hide, ragged wall ends, a strip of missing floor, cracked ceiling where props stood and holes where needles passed through. However good the steel, this is the part you look at every day, so it deserves the same care as the structure.
Worth knowing before you start
- Making good is easy to underestimate when budgeting. Removing a wall disturbs the ceiling, both wall ends and the floor, and props and needles leave their own marks, so the finishing work usually covers far more than the opening itself.
- Metal angle beads on every outside corner of the boxing give crisp, straight lines and protect the edges from knocks. They are set true to the ceiling and walls, so a slightly out-of-level beam does not show once skimmed.
- Victorian and Edwardian ceilings are often lath and lime plaster, which can sag or come away when nearby work shakes it. Small areas can be patched to match, while larger damaged areas are usually overboarded or replaced for a sound result.
- Fresh plaster has to dry before it is painted. A thin skim over board in a warm, ventilated room often dries within a few days to a week, while backing coats and deeper repairs take longer. Painting too soon can cause peeling and patchy colour.
- Fire-rated plasterboard is used for boxing steel that needs fire protection, while standard or moisture-resistant board suits ordinary ceiling and wall repairs. Using the right board in each place avoids rework when building control inspects.
How the job runs in Richmond
Free visit
A short visit to Richmond to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
What does plastering & making good cost in Richmond?
As a guide, budget £380–£1,540 including VAT for plastering and making good in Richmond, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £380–£1,540 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Chimney breast removal (ground floor) | £1,900–£3,850 | Ground-floor breast removed, steel to support the breast above, building control and making good |
| Fire protection to a steel beam | £190–£770 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Through-lounge knock-through | £3,200–£7,050 | Wall between front and back reception rooms, steel beam, approvals, plastering and floor infill |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Approvals in Richmond
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Questions about plastering & making good in Richmond
Can you work on older or listed homes in Richmond?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Do I need a party wall agreement for plastering & making good in Richmond?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
Will cracks appear after plastering?
Small hairline cracks can appear in the first months as the plaster dries and the building settles onto the new steel. They are cosmetic and normal, and are usually filled when you next repaint. Wide or growing cracks are different and should be reported, as they can point to movement that needs checking.
How do you hide a steel beam in the ceiling?
Most beams are boxed with fire-rated plasterboard fixed to a light frame, then finished with corner beads and a skim coat so they read as part of the ceiling. If you want no downstand at all, the beam has to be set into the floor void when it is installed, which is decided at the design stage.
What happens to the floor where the wall was removed?
The gap left by the wall is filled to match the floor on either side. Suspended timber floors get new joists and boards, solid floors are filled and screeded, and the infill is levelled so carpet, laminate or tiles can run straight across the room without a visible ridge.
Can I stay at home while the work is done in Richmond?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.