Plastering & making good · Cheltenham
Plastering & making good in Cheltenham
Plastering & making good for homes in GL50, GL51, GL52, designed by a structural engineer.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Cheltenham and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our plastering & making good service in Cheltenham
We carry out plastering & making good in Cheltenham, covering the GL50, GL51, GL52 and GL53 postcode districts. We also cover the surrounding towns and villages in Gloucestershire. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
We make good as the final stage of our structural jobs, and can quote it separately where another firm has fitted the steel. It covers boxing and fire boarding, plastering and skimming, floor infills and skirting, leaving smooth, dry surfaces for your decorator.
Key points for your project
- Plastering itself is wet rather than dusty, but cutting back old plaster and sanding filler is not. Work areas are sheeted off, floors protected and dust extraction used when cutting, so the mess stays in the room being worked on.
- New plaster is very absorbent, so the first coat of emulsion is normally thinned with water as a mist coat to seal it. Skipping this step is a frequent reason paint flakes off fresh plaster within weeks of decorating.
- Metal angle beads on every outside corner of the boxing give crisp, straight lines and protect the edges from knocks. They are set true to the ceiling and walls, so a slightly out-of-level beam does not show once skimmed.
- Fire-rated plasterboard is used for boxing steel that needs fire protection, while standard or moisture-resistant board suits ordinary ceiling and wall repairs. Using the right board in each place avoids rework when building control inspects.
- Textured ceiling coatings applied before 2000 can contain asbestos. Before a textured ceiling is cut, scraped or sanded, a sample is tested or an asbestos survey of the area is arranged, and the finish is only disturbed once the result is known.
How the job runs in Cheltenham
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
What does plastering & making good cost in Cheltenham?
As a guide, budget £310–£1,240 including VAT for plastering and making good in Cheltenham, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £310–£1,240 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Through-lounge knock-through | £2,600–£5,650 | Wall between front and back reception rooms, steel beam, approvals, plastering and floor infill |
| Fire protection to a steel beam | £150–£620 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Kitchen-diner knock-through | £2,600–£6,200 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Approvals in Cheltenham
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Plastering & making good near Cheltenham
- Tewkesbury 7.2 mi
- Gloucester 7.4 mi
- Stroud 11.6 mi
- Cirencester 13.3 mi
- Evesham 14.4 mi
- Great Malvern 18.0 mi
Plastering & making good in Cheltenham: your questions
How soon can plastering & making good start in Cheltenham?
Start dates depend on the engineer's calculations, the building control approval and, where needed, party wall notice periods. We give you a realistic timetable after the survey and keep you updated as each approval comes through.
What happens at the survey visit in Cheltenham?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Can you repair a lath and plaster ceiling?
Yes. Small areas can be patched with lath and lime-based plaster, or with board cut in and skimmed to match. Where large areas have sagged or pulled away from the laths, overboarding or replacing the ceiling is often the sounder repair. We assess the condition at the survey and price the right approach.
Do you decorate after making good?
Not usually. Making good leaves surfaces skimmed, dry and ready for paint, with trims refitted, and decoration is normally left to you or your decorator so you can choose colours and finishes yourself. Whoever paints should start with a thinned mist coat on the new plaster before the main coats.
How do you hide a steel beam in the ceiling?
Most beams are boxed with fire-rated plasterboard fixed to a light frame, then finished with corner beads and a skim coat so they read as part of the ceiling. If you want no downstand at all, the beam has to be set into the floor void when it is installed, which is decided at the design stage.
Can you work on older or listed homes in Cheltenham?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.