Plastering & making good · Gloucestershire
Plastering & making good in Gloucestershire
Plastering & making good across Gloucestershire, designed by a structural engineer and signed off by building control.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Gloucestershire and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What plastering & making good involves in Gloucestershire
Plastering and making good is the finishing work after a beam goes in or a wall comes out: boxing the steel, fixing corner beads, patching ceilings and wall ends, infilling the floor where the wall stood and skimming everything smooth. The aim is a room that looks as if the opening was always there, ready for paint.
Plastering & making good is one of the most common structural jobs in homes across Gloucestershire. That includes Cheltenham, Yate and Kingswood, plus smaller towns and villages nearby. Every job starts with a survey visit, then calculations from a structural engineer, so the steel suits the house in front of us rather than a rule of thumb.
What to expect
- New plaster is very absorbent, so the first coat of emulsion is normally thinned with water as a mist coat to seal it. Skipping this step is a frequent reason paint flakes off fresh plaster within weeks of decorating.
- Victorian and Edwardian ceilings are often lath and lime plaster, which can sag or come away when nearby work shakes it. Small areas can be patched to match, while larger damaged areas are usually overboarded or replaced for a sound result.
- Fresh plaster has to dry before it is painted. A thin skim over board in a warm, ventilated room often dries within a few days to a week, while backing coats and deeper repairs take longer. Painting too soon can cause peeling and patchy colour.
- Making good is the last chance to route cables neatly before surfaces close up. Sockets, switches and lights moved for the new layout are first-fixed before boarding, and pipes crossing the old wall line can run within the floor infill.
- A boxed beam usually leaves a downstand below the ceiling line. Where a flat ceiling is wanted, the beam has to be set up into the floor void during installation, so the finish needs deciding before the steel goes in, not after.
From survey to sign-off in Gloucestershire
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
How much should I budget in Gloucestershire?
As a guide, budget £310–£1,240 including VAT for plastering and making good in Gloucestershire, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £310–£1,240 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Kitchen-diner knock-through | £2,600–£6,200 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| Through-lounge knock-through | £2,600–£5,650 | Wall between front and back reception rooms, steel beam, approvals, plastering and floor infill |
| Load-bearing wall removal with steel beam | £2,050–£5,150 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Building control and neighbours in Gloucestershire
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Plastering & making good by town
Plastering & making good in Gloucestershire: your questions
Can you work on older or listed homes in Gloucestershire?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Do you cover Gloucestershire for plastering & making good?
Yes. We carry out plastering & making good in Gloucestershire. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Do you replace skirting boards and door frames after a knock-through?
Yes, where the work affects them. Skirting is extended or replaced so it runs through the new opening, and door linings and architraves are refitted or replaced where an opening has changed. Where period mouldings are involved, matching profiles can usually be sourced or made up to suit.
Can you repair a lath and plaster ceiling?
Yes. Small areas can be patched with lath and lime-based plaster, or with board cut in and skimmed to match. Where large areas have sagged or pulled away from the laths, overboarding or replacing the ceiling is often the sounder repair. We assess the condition at the survey and price the right approach.
How do you hide a steel beam in the ceiling?
Most beams are boxed with fire-rated plasterboard fixed to a light frame, then finished with corner beads and a skim coat so they read as part of the ceiling. If you want no downstand at all, the beam has to be set into the floor void when it is installed, which is decided at the design stage.
Can you match my old textured ceiling?
Often, yes, although a perfect match is hard over large patches. Before anything is touched, a textured coating applied before 2000 is tested for asbestos. Small areas can then be re-textured to blend in, while many people choose to skim the whole ceiling flat for a cleaner, consistent finish.
Which towns in Gloucestershire do you cover?
We cover towns including Gloucester, Cheltenham, Stroud and Kingswood, plus the villages and smaller towns around them.