Loft conversion steels · Felling
Loft conversion steels in Felling
Loft conversion steels for homes in NE8, NE9, NE10, designed by a structural engineer.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Felling and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our loft conversion steels service in Felling
We cover loft conversion steels in Felling (NE8, NE9, NE10) and the streets around it. Felling is around 2.2 miles from Newcastle upon Tyne, and we cover both. Each job is designed by a structural engineer and approved through Gateshead Council before work begins.
We fit the steel package for loft conversions, either as part of the full project or alongside your loft builder. That means the engineer's design, building control, getting long steels into a roof space safely, bedding them on padstones and packing them before the new floor and dormer go on.
What to expect
- Traditional cut roofs rely on purlins and struts running down to internal walls. A steel beam can take over that job so the struts come out, freeing up floor and headroom, but the change has to be designed and propped carefully.
- Many later twentieth-century homes have trussed rafter roofs, with diagonal timbers running through the whole loft. Converting these involves more steel and new timber, because each truss is cut and its load has to be re-routed by design.
- A rear dormer removes part of the roof slope, so the rafters above lose their support at the lower end. A ridge beam or a beam along the dormer's front edge carries them instead, designed for the dormer width and the weight of the roof.
- In older terraces the party wall at loft level can be thin, built in soft brick, or contain old chimney flues. The engineer may avoid bearing over a flue, ask for a section of wall to be rebuilt, or use a post down to firmer support.
- Building regulations also cover escape from the new room in a fire. In a typical house that often means a protected stairway with fire doors from the loft down to an exit, so the steel design sits within a wider fire safety approval.
What happens, step by step
Free visit
A short visit to Felling to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to Gateshead Council, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
How much should I budget in Felling?
As a guide, budget £2,300–£5,600 including VAT for loft conversion steels in Felling, based on published UK cost guides adjusted for prices in the North East (-7%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £2,300–£5,600 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Steel column or post | £460–£1,400 per column | Column supplied and fitted with base and cap plates on a pad foundation |
| Temporary works and propping | £140–£460 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Fire protection to a steel beam | £140–£560 per beam | Fire-rated board boxing or an intumescent coating system as specified |
Figures include our approximate regional adjustment for prices in the North East (-7%) and are rounded. How these figures are worked out.
Building control and neighbours in Felling
For Felling, building control is provided by Gateshead Council, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Local questions answered
Do you also work near Felling?
Yes. We also cover nearby towns including Gateshead, Newcastle upon Tyne, Hebburn and Wallsend.
What happens at the survey visit in Felling?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
How long does it take to install loft steels?
The main steels for a typical loft conversion usually go in over two to five working days. That covers cutting pockets, bedding padstones, getting the steel in and packing it. The timing depends heavily on access and how many beams the design calls for.
What is a ridge beam in a loft conversion?
A ridge beam is a steel beam running along the top of the roof to support the rafters when their usual support is removed, such as when a large dormer is built or a hipped roof is converted to a gable. The engineer decides whether one is needed and specifies it.
Do all loft conversions need steel beams?
Most do, but not all. Steels are usually needed to carry the new floor, replace purlins and struts, or support the roof around a dormer. Some smaller conversions use deeper timber joists or engineered timber instead. A structural engineer decides what the roof and walls need after a survey.