Loft conversion steels · Egham
Loft conversion steels in Egham
Steelwork, approvals and making good for loft conversion steels in Egham and nearby.
- Survey, design and installation in one
- Covering GU25, TW18, TW19
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning loft conversion steels in Egham
Planning loft conversion steels in Egham? Our team covers GU25, TW18, TW19 and TW20 and the streets around them. It sits about 5.7 miles from Slough, which we also cover. You get one written quote for the calculations, approvals, propping, steel and making good.
The joists in most lofts were only ever meant to hold up a plaster ceiling, and the roof is often propped on struts and purlins that get in the way of a room. Steel beams solve both problems: they carry a new floor across the house and take over the roof support so the struts can come out.
What to expect
- Building regulations also cover escape from the new room in a fire. In a typical house that often means a protected stairway with fire doors from the loft down to an exit, so the steel design sits within a wider fire safety approval.
- Steels supporting a loft floor commonly need 30-minute fire resistance in a typical house. That is usually achieved with fire-rated plasterboard below and around the steel, to the specification agreed with building control.
- Cutting pockets into a party wall for steel bearings is notifiable work in England and Wales under the Party Wall etc. Act 1996. A party structure notice must be served at least two months before that work starts, so it is worth raising early in the planning.
- Headroom in the finished loft depends partly on where the floor steels sit. Setting them low, between the existing ceiling joists, keeps more height upstairs, and the engineer and loft designer agree the levels together.
- In older terraces the party wall at loft level can be thin, built in soft brick, or contain old chimney flues. The engineer may avoid bearing over a flue, ask for a section of wall to be rebuilt, or use a post down to firmer support.
What happens, step by step
Free visit
A short visit to Egham to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
Guide prices for loft conversion steels in Egham
As a guide, budget £2,800–£6,700 including VAT for loft conversion steels in Egham, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £2,800–£6,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Fire protection to a steel beam | £170–£670 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Temporary works and propping | £170–£560 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Steel column or post | £560–£1,680 per column | Column supplied and fitted with base and cap plates on a pad foundation |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Egham
For Egham, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Questions about loft conversion steels in Egham
Do I need a party wall agreement for loft conversion steels in Egham?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
Do you cover Egham for loft conversion steels?
Yes. We carry out loft conversion steels in Egham and the GU25, TW18, TW19 and TW20 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Can my loft be converted if it has trussed rafters?
Often it can, but it is a bigger structural job. Trussed rafters have diagonal webs right through the loft, and every truss that is cut needs its load picked up by new steel and timber. The engineer designs that, and the roof is propped carefully throughout.
Can I stay in my house during a loft conversion?
Usually, yes. Most of the steel work happens in the roof space, with access through the loft hatch or a roof opening, so the rest of the house stays usable. Expect noise while pockets are cut into the walls and some dust on the landing, which is screened off.
How do you get steel beams into a loft?
It depends on access. Beams are often passed in through an opening made in the roof or a gable window, or brought up in shorter sections and bolted together in the loft where the engineer's design allows. For long or heavy steels a hoist or crane may be used, planned in advance.
What happens at the survey visit in Egham?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.