Loft conversion steels · Feltham
Loft conversion steels in Feltham
Steelwork, approvals and making good for loft conversion steels in Feltham and nearby.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our loft conversion steels service in Feltham
Our loft conversion steels service in Feltham covers everything from the first visit to the completion paperwork. Our coverage runs across London, so nearby villages are included too. Postcode districts we cover here include TW2, TW3, TW4, TW5 and TW6.
The joists in most lofts were only ever meant to hold up a plaster ceiling, and the roof is often propped on struts and purlins that get in the way of a room. Steel beams solve both problems: they carry a new floor across the house and take over the roof support so the struts can come out.
Worth knowing before you start
- Traditional cut roofs rely on purlins and struts running down to internal walls. A steel beam can take over that job so the struts come out, freeing up floor and headroom, but the change has to be designed and propped carefully.
- The steel stage of a loft conversion usually takes a few working days and comes early, before floor joists, dormer framing and insulation. Keep the steel calculations with the completion certificate, as both are asked for when the house is sold.
- Building regulations also cover escape from the new room in a fire. In a typical house that often means a protected stairway with fire doors from the loft down to an exit, so the steel design sits within a wider fire safety approval.
- A rear dormer removes part of the roof slope, so the rafters above lose their support at the lower end. A ridge beam or a beam along the dormer's front edge carries them instead, designed for the dormer width and the weight of the roof.
- Headroom in the finished loft depends partly on where the floor steels sit. Setting them low, between the existing ceiling joists, keeps more height upstairs, and the engineer and loft designer agree the levels together.
Four stages, one team
Survey in Feltham
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Feltham?
As a guide, budget £3,200–£7,700 including VAT for loft conversion steels in Feltham, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £3,200–£7,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Temporary works and propping | £190–£640 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| RSJ supply and fit (single beam) | £1,000–£3,200 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Structural calculations for a beam | £320–£960 | Site measure or photos, beam and padstone design and calculations for building control |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building rules for Feltham
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Questions about loft conversion steels in Feltham
How much do loft conversion steels cost in Feltham?
As a guide, budget £3,200–£7,700 including VAT for loft conversion steels in Feltham, based on published UK cost guides adjusted for London prices (+28%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
Can I stay at home while the work is done in Feltham?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
How long does it take to install loft steels?
The main steels for a typical loft conversion usually go in over two to five working days. That covers cutting pockets, bedding padstones, getting the steel in and packing it. The timing depends heavily on access and how many beams the design calls for.
Do loft conversion steels need fire protection?
Usually, yes. Steel loses strength in a fire, and the beams carrying the new floor are elements of structure. In a typical house they commonly need 30-minute fire resistance, often provided by fire-rated plasterboard around and below the steel, as agreed with building control.
What is a ridge beam in a loft conversion?
A ridge beam is a steel beam running along the top of the roof to support the rafters when their usual support is removed, such as when a large dormer is built or a hipped roof is converted to a gable. The engineer decides whether one is needed and specifies it.