Loft conversion steels · Yeovil
Loft conversion steels in Yeovil
Loft conversion steels for homes in BA20, BA21, BA22, designed by a structural engineer.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our loft conversion steels service in Yeovil
We carry out loft conversion steels in Yeovil, covering the BA20, BA21 and BA22 postcode districts. We also cover the surrounding towns and villages in Somerset. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
We fit the steel package for loft conversions, either as part of the full project or alongside your loft builder. That means the engineer's design, building control, getting long steels into a roof space safely, bedding them on padstones and packing them before the new floor and dormer go on.
Key points for your project
- A rear dormer removes part of the roof slope, so the rafters above lose their support at the lower end. A ridge beam or a beam along the dormer's front edge carries them instead, designed for the dormer width and the weight of the roof.
- Headroom in the finished loft depends partly on where the floor steels sit. Setting them low, between the existing ceiling joists, keeps more height upstairs, and the engineer and loft designer agree the levels together.
- Cutting pockets into a party wall for steel bearings is notifiable work in England and Wales under the Party Wall etc. Act 1996. A party structure notice must be served at least two months before that work starts, so it is worth raising early in the planning.
- In older terraces the party wall at loft level can be thin, built in soft brick, or contain old chimney flues. The engineer may avoid bearing over a flue, ask for a section of wall to be rebuilt, or use a post down to firmer support.
- Many later twentieth-century homes have trussed rafter roofs, with diagonal timbers running through the whole loft. Converting these involves more steel and new timber, because each truss is cut and its load has to be re-routed by design.
What happens, step by step
Free visit
A short visit to Yeovil to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
What do loft conversion steels cost in Yeovil?
As a guide, budget £2,600–£6,200 including VAT for loft conversion steels in Yeovil, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £2,600–£6,200 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Steel column or post | £520–£1,540 per column | Column supplied and fitted with base and cap plates on a pad foundation |
| Structural calculations for a beam | £260–£770 | Site measure or photos, beam and padstone design and calculations for building control |
| RSJ supply and fit (single beam) | £820–£2,580 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Building rules for Yeovil
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Loft conversion steels near Yeovil
- Bridgwater 20.7 mi
- Taunton 21.1 mi
- Weymouth 23.8 mi
- Frome 23.9 mi
Loft conversion steels in Yeovil: your questions
How much do loft conversion steels cost in Yeovil?
As a guide, budget £2,600–£6,200 including VAT for loft conversion steels in Yeovil, based on published UK cost guides adjusted for prices in the South West (+3%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
Can you work on older or listed homes in Yeovil?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Where do loft conversion steels sit?
Usually between the gable walls or party walls, bearing on padstones bedded into pockets cut in the brickwork. Floor beams sit low, close to the existing ceiling, while ridge or dormer beams sit higher up to support the roof. The engineer sets the exact positions and levels.
Do loft conversion steels need fire protection?
Usually, yes. Steel loses strength in a fire, and the beams carrying the new floor are elements of structure. In a typical house they commonly need 30-minute fire resistance, often provided by fire-rated plasterboard around and below the steel, as agreed with building control.
Can my loft be converted if it has trussed rafters?
Often it can, but it is a bigger structural job. Trussed rafters have diagonal webs right through the loft, and every truss that is cut needs its load picked up by new steel and timber. The engineer designs that, and the roof is propped carefully throughout.
Do you also work near Yeovil?
Yes. We also cover nearby towns including Bridgwater, Taunton, Weymouth and Frome.