Fire protection for steel beams · Perth
Fire protection for steel beams in Perth
Fire protection for steel beams for homes in PH1, PH2, designed by a structural engineer.
- Price fixed in writing once scope is agreed
- Building warrant arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning fire protection for steel beams in Perth
If you live in Perth, fire protection for steel beams can usually be planned and priced after a single survey visit. The wider Perth and Kinross area is covered as well. We cover PH1 and PH2, and we fix the price in writing once the layout and scope are agreed.
We fit fire protection alongside new steelwork, and as a standalone job where steel was installed without it or building standards has asked for more. That covers boxing with fire-rated plasterboard, intumescent coatings for steel left on show, and the records building standards needs to see before signing the work off.
Key points for your project
- Boarding is fairly clean work, but coatings need a clean, dry and well-ventilated room at a suitable temperature. Dust from other trades can spoil the surface, so painting is normally scheduled once the messy work in that room is finished.
- Older homes sometimes have steel fitted decades ago with no protection at all, or boxed in ordinary timber and hardboard. When this turns up during other work, we can check what is there and price protection to suit today's requirements.
- Building standards treats fire protection as part of the structural approval, not an optional extra. If unprotected steel is found at inspection, the completion certificate is normally held back until the protection is in place and has been checked.
- Boxing is generally the lower-cost route for steel that will be hidden. Intumescent coatings cost more because of the product and the number of coats, and the price rises with the fire period and the size of the section.
- Fire boarding should not be cut into casually later on. Downlights, cables and pipes pushed through the boxing can weaken it, so services are planned before boarding, and any openings are sealed with suitable fire-stopping materials.
How the job runs in Perth
Survey in Perth
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building warrant
A building warrant is applied for from Perth and Kinross Council, and work starts only once the warrant has been granted.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building standards inspects it, and we make good.
What does fire protection for steel beams cost in Perth?
As a guide, budget £140–£550 per beam including VAT for fire protection to a steel beam in Perth, based on published UK cost guides adjusted for prices in Scotland (-9%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Fire protection to a steel beam | £140–£550 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Plastering and making good | £270–£1,090 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Steel column or post | £460–£1,360 per column | Column supplied and fitted with base and cap plates on a pad foundation |
| Structural calculations for a beam | £230–£680 | Site measure or photos, beam and padstone design and calculations for building standards |
Figures include our approximate regional adjustment for prices in Scotland (-9%) and are rounded. How these figures are worked out.
Building control and neighbours in Perth
Scottish rules are stricter on timing than in England: the building warrant must be in place before the wall is touched. We prepare the application with the engineer's calculations and submit it to Perth and Kinross Council. The finished work is then certified and a completion certificate submitted for acceptance.
Scotland has no Party Wall Act. Work affecting a shared wall is governed by your title deeds and the general law, and in flats by the Tenements (Scotland) Act 2004, so it is sensible to agree the work with neighbours in writing before starting.
Fire protection for steel beams near Perth
- Auchterarder 12.6 mi
- Kinross 13.1 mi
- Blairgowrie 13.9 mi
- Crieff 15.7 mi
- Glenrothes 17.0 mi
- Tillicoultry 20.5 mi
Questions about fire protection for steel beams in Perth
Do you also work near Perth?
Yes. We also cover nearby towns including Auchterarder, Kinross, Blairgowrie and Crieff.
Who approves fire protection for steel beams in Perth?
Structural work in Perth needs a building warrant from Perth and Kinross Council, granted before work starts. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Does a steel column need fire protection as well as the beam?
Usually, if the column is part of the load path. A column carrying a beam is just as important in a fire, so it normally needs the same fire resistance. Columns are often boxed with board or coated with intumescent paint, and the engineer's design and building standards confirm what applies to yours.
How long does intumescent paint take to apply?
Several days in most cases. Each coat has to dry before the next is applied, and the number of coats depends on the thickness needed. Cold or damp rooms slow drying, so the space is kept warm and ventilated, and the top coat goes on once the full build has been measured.
Can I box in a steel beam with normal plasterboard?
Not where fire protection is required. Standard plasterboard is not designed to protect steel for a set period in a fire. Fire-rated plasterboard is used instead, fixed in the number of layers and with the fixings the system specifies, so the boxing performs as intended and passes when building standards checks it.
Can you work on older or listed homes in Perth?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.