Bi-fold & sliding door openings · Wallington
Bi-fold & sliding door openings in Wallington
Steelwork, approvals and making good for bi-fold & sliding door openings in Wallington and nearby.
- Free survey visit in Wallington
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Bi-fold & sliding door openings in Wallington: how it works
We cover bi-fold & sliding door openings in Wallington (CR4, CR8, SM1) and the streets around it. Our coverage runs across London, so nearby villages are included too. Each job is designed by a structural engineer and approved through local building control before work begins.
Replacing a window or narrow patio door with a full run of bi-fold or sliding doors opens a room to the garden. Because it is an external wall, the opening usually carries the first floor, the wall above and sometimes roof loads, and the new steel has to work with the doors as well as hold the house up.
Key points for your project
- New glazed doors must meet the energy efficiency requirements of the building regulations, and a wide opening adds a large area of glazing to the house. The door supplier normally provides the performance data that building control needs.
- The house is open to the weather between taking out the wall and fitting the doors. Temporary sheeting or a boarded frame keeps rain out and the house secure, so the gap between the structural work and door fitting should be kept short.
- Glazed doors need a stiffer beam than a plain opening of the same width. If the steel bends even slightly under load, folding panels can bind, sliders can stick and glass can be stressed, so the engineer sets a tighter deflection limit for door openings.
- External walls can have gas meters, boiler flues, soil pipes, outside taps or cables near the new opening. These are found at survey and moved by the right trade, with any gas pipework done by a Gas Safe registered engineer as the law requires.
- New brickwork at the reveals and above the opening should match the existing in colour, size and bond. Sound bricks from the wall being removed are often cleaned and reused, and the mortar colour is matched as closely as possible.
From survey to sign-off in Wallington
Survey in Wallington
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for bi-fold & sliding door openings in Wallington
As a guide, budget £3,200–£8,950 including VAT for rear wall opening for bi-fold or sliding doors in Wallington, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £3,200–£8,950 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| Steel goalpost frame | £2,550–£7,700 | Two posts and a beam bolted as a frame, pad foundations, base plates and fitting |
| Widening an internal doorway | £1,300–£3,200 | Opening widened with a new lintel or short beam, approval where structural, and making good |
| Lintel replacement | £510–£1,540 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Approvals in Wallington
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Bi-fold & sliding door openings near Wallington
- Carshalton 0.7 mi
- Sutton 2.2 mi
- South Croydon 2.6 mi
- Purley 2.6 mi
- Croydon 2.7 mi
- Mitcham 2.8 mi
Local questions answered
Do you also work near Wallington?
Yes. We also cover nearby towns including Carshalton, Sutton, South Croydon and Purley.
Can you work on older or listed homes in Wallington?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
How long does it take to make an opening for bi-fold doors?
The structural opening usually takes three to five working days, including propping, cutting out the wall, fitting the steel and outer leaf support, and forming the reveals. The doors can then be fitted, with inside making good and outside brickwork finishing following on. Lead times on made-to-order doors affect the overall timeline more than the steelwork.
Why does the beam need to be stiffer for glazed doors?
Because glazed doors tolerate very little movement. Every beam bends slightly under load, and with bi-folds or sliders that movement can make panels bind, tracks drag or glass crack. The engineer sets a stricter deflection limit for these openings, which often means a heavier section than strength alone would need.
Do I need planning permission for bi-fold doors?
Usually not for a rear opening in a house, as this generally falls within permitted development. Planning or another consent may be needed for front elevations, flats, listed buildings, conservation areas with extra controls, or homes where permitted development rights have been removed. We flag this at survey so you can check before work is booked.