Wider doorways & openings · Barking
Wider doorways & openings in Barking
Steelwork, approvals and making good for wider doorways & openings in Barking and nearby.
- Survey, design and installation in one
- Covering E6, E12, E20
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Wider doorways & openings in Barking: how it works
If you live in Barking, wider doorways & openings can usually be planned and priced after a single survey visit. Our coverage runs across London, so nearby villages are included too. We cover E6, E12, E20, IG1 and IG3, and we fix the price in writing once the layout and scope are agreed.
We arrange a survey visit, structural calculations where the wall is load-bearing, building control, propping, the lintel or beam, new door linings if you want them, and making good. One itemised written quote covers the lot, and the price is fixed in writing once the opening size and finish are agreed.
Things to plan for
- Each side of the new opening needs enough solid wall for the lintel or beam to sit on. If the opening runs close to a corner, another doorway or a chimney breast, there may not be enough masonry, and a column or padstone may be required.
- Hallway walls are often load-bearing because they line up with walls upstairs and carry the floor joists or the stairs. A wall that sounds hollow when knocked is usually a stud partition, but older homes can have timber walls that still carry loads, so the engineer checks.
- Standard internal doors come in set widths, so it makes sense to size the opening to suit an off-the-shelf door and lining. Odd sizes need made-to-measure doors and linings, which take longer to arrange.
- In older houses, a doorway may already have a timber lintel that has rotted or a brick arch that is hard to extend. These are replaced rather than added to, and the engineer allows for soft lime mortar and any cracking found once the wall is opened.
- Widening a single doorway in a load-bearing wall usually takes one to two days for the structural work. The plaster then needs time to dry before the door linings are decorated or a new door is hung.
What happens, step by step
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
How much should I budget in Barking?
As a guide, budget £1,300–£3,200 including VAT for widening an internal doorway in Barking, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Widening an internal doorway | £1,300–£3,200 | Opening widened with a new lintel or short beam, approval where structural, and making good |
| Lintel replacement | £510–£1,540 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
| Structural calculations for a beam | £320–£960 | Site measure or photos, beam and padstone design and calculations for building control |
| Load-bearing wall removal with steel beam | £2,550–£6,400 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Approvals in Barking
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Wider doorways & openings near Barking
- Ilford 1.7 mi
- Becontree 2.4 mi
- Thamesmead 2.6 mi
- Canning Town 3.1 mi
- Stratford 3.6 mi
- Dagenham 3.8 mi
Questions about wider doorways & openings in Barking
What happens at the survey visit in Barking?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Can you work on older or listed homes in Barking?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Do I need building regulations to widen an internal door?
Only if the wall is load-bearing or the change affects fire safety, such as the escape route from upstairs. Widening an opening in a non-structural stud partition usually does not need structural approval. We confirm which applies at the survey, and handle the building control application or notice where it is needed.
How long does it take to widen a doorway?
The structural part usually takes one to two working days: propping, cutting the opening, fitting the lintel or beam and packing it. Plastering follows, then a few days of drying before linings are painted or a new door is hung. Building control inspection fits in once the support is in place.
Is a lintel or a steel beam needed for a wider door?
It depends on the loads. A lintel can be enough for a modest widening under light loads, while an opening carrying floor joists or a wall above usually needs steel. The engineer decides from the actual loads and span rather than the width alone, and we fit whichever is specified.