Temporary works & propping · Leigh
Temporary works & propping in Leigh
Temporary works & propping in Leigh, from free survey to completion certificate.
- Free survey visit in Leigh
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning temporary works & propping in Leigh
We cover temporary works & propping in Leigh (M29, M46, WN7) and the streets around it. We also work in nearby Wigan, roughly 5.8 miles away. Each job is designed by a structural engineer and approved through Wigan Council before work begins.
The moment a load-bearing wall is cut, whatever it was holding needs another route to the ground. Temporary works provide that route. Done well, nothing above moves, ceilings stay intact and the floor below is not overloaded. Done badly, it is where structural work goes wrong.
Things to plan for
- The order of work matters. Props go in and are tightened before any masonry is cut, the opening is formed in stages, and the props stay until the permanent steel is packed tight and the bedding mortar has gained enough strength.
- For simple openings, the engineer's calculations usually show the propping arrangement. Larger or unusual jobs, such as removing several walls or working beneath chimney stacks, may need a separate temporary works design prepared by an engineer.
- Props and needles cannot go where pipes, cables or flues run. Their positions are checked against services before any holes are cut, and anything in the way is isolated or rerouted first by the appropriate trade.
- Propping costs depend on how many props and needles the load calls for, how long they stay in, whether a separate temporary works design is required, and whether props must continue through a floor to reach solid ground.
- Typical mistakes include props standing on unsupported floorboards, missing spreaders so one joist takes all the load, and props wound up too hard so the ceiling lifts and cracks. Careful setting out and gradual tightening avoid all three.
From survey to sign-off in Leigh
Survey in Leigh
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to Wigan Council, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
What do temporary works & propping cost in Leigh?
As a guide, budget £140–£480 including VAT for temporary works and propping in Leigh, based on published UK cost guides adjusted for prices in the North West (-4%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Temporary works and propping | £140–£480 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Structural calculations for a beam | £240–£720 | Site measure or photos, beam and padstone design and calculations for building control |
| RSJ supply and fit (single beam) | £770–£2,400 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Lintel replacement | £380–£1,150 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
Figures include our approximate regional adjustment for prices in the North West (-4%) and are rounded. How these figures are worked out.
Building control and neighbours in Leigh
For Leigh, building control is provided by Wigan Council, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Temporary works & propping near Leigh
- Atherton 2.2 mi
- Tyldesley 2.5 mi
- Golborne 3.4 mi
- Westhoughton 3.6 mi
- Hindley 3.7 mi
- Newton-le-Willows 4.6 mi
Local questions answered
Do I need a party wall agreement for temporary works & propping in Leigh?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
Do you also work near Leigh?
Yes. We also cover nearby towns including Atherton, Tyldesley, Golborne and Westhoughton.
Can I stay in my house while it is propped?
Usually, yes. The props take up space in the rooms either side of the work, so those rooms will be out of use, but the rest of the house can be lived in as normal. The props must never be moved, knocked or adjusted by anyone other than the installation team.
Can I hire props and support a wall myself?
Props can be hired, but propping a structure is skilled work with serious consequences if it goes wrong. The arrangement should come from an engineer's design, and the loads, floor strength and sequence all need checking. Structural propping should be left to a competent team working to that design.
What is needling a wall?
Needling means cutting holes through a wall just above where an opening will go and passing short steel beams, called needles, through them. Each needle is supported on props on both sides, so the masonry above rests on the needles while the wall below is removed and the permanent beam is fitted.
What happens at the survey visit in Leigh?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.