Structural calculations · Bognor Regis
Structural calculations in Bognor Regis
Structural calculations for homes in PO21, PO22, designed by a structural engineer.
- Survey, design and installation in one
- Covering PO21, PO22
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What structural calculations involve in Bognor Regis
Planning structural calculations in Bognor Regis? Our team covers PO21 and PO22 and the streets around them. Bognor Regis is around 13.5 miles from Worthing, and we cover both. You get one written quote for the calculations, approvals, propping, steel and making good.
We arrange the calculations as part of every structural job, or work to calculations you already have if they match the design. The engineer's output goes to building control with the application, and the same figures guide the steel order, the padstones and the propping on site.
What to expect
- The calculations or the building control approval usually state the fire resistance the steel needs, commonly 30 minutes in typical houses. That requirement then decides whether the beam is boxed in fire-rated plasterboard, painted with intumescent coating or protected another way.
- Calculations can also cover how the structure is held up during the work. For straightforward openings this may be a note on prop positions, while larger or more complex jobs may need a separate temporary works design.
- The beam ends are designed as carefully as the beam. Calculations check that the masonry under each end can take the concentrated load, and specify a padstone, spreader or column where it cannot. Weak brickwork beneath a bearing is a common reason for design changes.
- Older buildings take more judgement. Lime mortar, rubble-filled walls, timber bressummers and shallow footings all affect how loads are carried, so engineers working on period properties often allow for weaker materials or ask for more investigation.
- Building control uses the calculations to check compliance with Part A of the Building Regulations in England and Wales, or the equivalent structural standards in Scotland and Northern Ireland. Without them, an application for structural work is unlikely to be approved.
What happens, step by step
Survey in Bognor Regis
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
What do structural calculations cost in Bognor Regis?
As a guide, budget £280–£840 including VAT for structural calculations for a beam in Bognor Regis, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Structural calculations for a beam | £280–£840 | Site measure or photos, beam and padstone design and calculations for building control |
| Loft conversion steels | £2,800–£6,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Steel beam replacement | £2,250–£6,150 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Building control fees | £280–£730 | Building notice or full plans fee and inspections; varies by council or approver |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Approvals in Bognor Regis
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Structural calculations near Bognor Regis
- Chichester 5.8 mi
- Littlehampton 6.4 mi
- Worthing 13.5 mi
- Havant 14.3 mi
- Waterlooville 16.7 mi
- Portsmouth 18.0 mi
Structural calculations in Bognor Regis: your questions
Who approves structural calculations in Bognor Regis?
Structural work in Bognor Regis needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
What happens at the survey visit in Bognor Regis?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Do I need calculations for an old beam when selling my house?
Often a buyer's surveyor or solicitor will ask for them if there is no record of the beam being approved. An engineer can inspect the existing steel, check it against the loads and issue calculations or a report. In England and Wales these can support a regularisation application for retrospective approval.
Do I need structural calculations to remove a wall?
Yes, if the wall is load-bearing. Building control needs calculations showing that the new beam, its bearings and anything supporting it can carry the loads safely. Non-structural stud partitions normally do not need them, but an engineer should confirm a wall is non-structural before anyone assumes it.
What is a load take-down?
A load take-down is the part of the calculations that adds up every load reaching a beam or column and follows it down to the ground. It includes the roof, floors, walls, people, furniture and, where relevant, snow and wind. Each element along that path is then checked to make sure it can carry its share.
Can I stay at home while the work is done in Bognor Regis?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.