Structural calculations · Tyne and Wear
Structural calculations in Tyne and Wear
Structural calculations across Tyne and Wear, designed by a structural engineer and signed off by building control.
- Survey, design and installation in one
- Covering DH4, DH5, NE1, NE10
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Structural calculations in Tyne and Wear: how it works
Structural calculations are an engineer's written design showing that a beam, column or other structural element can safely carry the loads placed on it. For steel beam work they set out the loads from floors, walls and roof, the steel section, the padstones or columns at each end and any propping requirements, and they are submitted to building control.
We carry out structural calculations throughout Tyne and Wear, for homeowners, landlords and builders who need the structural part done properly. We work in North Shields, South Shields and Washington and the surrounding villages. You get an itemised written quote that shows the calculations, approvals, steel, labour and finishing as separate lines.
What to expect
- How long calculations take depends on the engineer's workload and how complicated the job is. A single beam is quicker to design than a loft conversion with several steels, and any opening up needed for investigation adds time before figures can be issued.
- A load take-down traces every weight that reaches the beam, from roof tiles and snow to upstairs walls, furniture and people. Getting this right matters as much as the beam choice itself, because an underestimated load makes every later check wrong.
- Opening up can reveal things no survey could see, such as a hidden chimney flue, joists running the other way or a wall with no footing. When that happens, the engineer revises the design before work continues, and any change is priced before it goes ahead.
- The cost of calculations rises with complexity: the number of beams and columns, whether loads come down from several floors, whether foundations need designing, and how much investigation is needed on site. A single straightforward beam sits at the simpler end.
- A typical calculation pack covers the loads assumed, the beam section chosen, checks for bending, shear and deflection, the bearing and padstone design, and any column or foundation design. It is usually accompanied by a drawing or sketch showing positions.
What happens, step by step
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
Guide prices for structural calculations in Tyne and Wear
As a guide, budget £230–£700 including VAT for structural calculations for a beam in Tyne and Wear, based on published UK cost guides adjusted for prices in the North East (-7%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Structural calculations for a beam | £230–£700 | Site measure or photos, beam and padstone design and calculations for building control |
| Loft conversion steels | £2,300–£5,600 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Steel beam replacement | £1,850–£5,100 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Load-bearing wall removal with steel beam | £1,850–£4,650 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
Figures include our approximate regional adjustment for prices in the North East (-7%) and are rounded. How these figures are worked out.
Approvals in Tyne and Wear
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Structural calculations in Tyne and Wear: your questions
Do I need a party wall agreement for structural calculations in Tyne and Wear?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
What happens at the survey visit in Tyne and Wear?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
What is a load take-down?
A load take-down is the part of the calculations that adds up every load reaching a beam or column and follows it down to the ground. It includes the roof, floors, walls, people, furniture and, where relevant, snow and wind. Each element along that path is then checked to make sure it can carry its share.
Do I need structural calculations to remove a wall?
Yes, if the wall is load-bearing. Building control needs calculations showing that the new beam, its bearings and anything supporting it can carry the loads safely. Non-structural stud partitions normally do not need them, but an engineer should confirm a wall is non-structural before anyone assumes it.
Do I need calculations for an old beam when selling my house?
Often a buyer's surveyor or solicitor will ask for them if there is no record of the beam being approved. An engineer can inspect the existing steel, check it against the loads and issue calculations or a report. In England and Wales these can support a regularisation application for retrospective approval.
What do structural calculations for a steel beam include?
They include the loads the beam carries, the steel section chosen, checks for bending, shear and deflection, and the design of the padstones or columns at each end. Most packs also come with a drawing or sketch showing positions and bearing details, and note the fire protection and any propping requirements.
Can I stay at home while the work is done in Tyne and Wear?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.