Structural calculations · Wigan
Structural calculations in Wigan
Steelwork, approvals and making good for structural calculations in Wigan and nearby.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Structural calculations in Wigan: how it works
We carry out structural calculations in Wigan, covering the WN1, WN2, WN3, WN5 and WN6 postcode districts. We also cover the surrounding towns and villages in Greater Manchester. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
Building control will not approve a beam on trust. Before steel goes in, someone has to show in writing what the beam is carrying, what size it needs to be and how its ends are supported. That is the job of structural calculations, prepared by a qualified structural engineer from measurements taken at the property.
Worth knowing before you start
- The calculations or the building control approval usually state the fire resistance the steel needs, commonly 30 minutes in typical houses. That requirement then decides whether the beam is boxed in fire-rated plasterboard, painted with intumescent coating or protected another way.
- A load take-down traces every weight that reaches the beam, from roof tiles and snow to upstairs walls, furniture and people. Getting this right matters as much as the beam choice itself, because an underestimated load makes every later check wrong.
- How long calculations take depends on the engineer's workload and how complicated the job is. A single beam is quicker to design than a loft conversion with several steels, and any opening up needed for investigation adds time before figures can be issued.
- Keep the final calculations and drawings with the building control completion certificate. Together they show a future buyer, lender or surveyor exactly what was installed and why, and they help any later alterations to build on a known design.
- Building control uses the calculations to check compliance with Part A of the Building Regulations in England and Wales, or the equivalent structural standards in Scotland and Northern Ireland. Without them, an application for structural work is unlikely to be approved.
Four stages, one team
Survey in Wigan
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to Wigan Council, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for structural calculations in Wigan
As a guide, budget £240–£720 including VAT for structural calculations for a beam in Wigan, based on published UK cost guides adjusted for prices in the North West (-4%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Structural calculations for a beam | £240–£720 | Site measure or photos, beam and padstone design and calculations for building control |
| Temporary works and propping | £140–£480 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Loft conversion steels | £2,400–£5,750 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| RSJ supply and fit (single beam) | £770–£2,400 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for prices in the North West (-4%) and are rounded. How these figures are worked out.
Approvals in Wigan
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either Wigan Council or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Structural calculations near Wigan
- Hindley 2.3 mi
- Ashton in Makerfield 4.2 mi
- Westhoughton 4.6 mi
- Golborne 4.9 mi
- Skelmersdale 5.6 mi
- Leigh 5.8 mi
Local questions answered
Do you also work near Wigan?
Yes. We also cover nearby towns including Hindley, Ashton in Makerfield, Westhoughton and Golborne.
Do you cover Wigan for structural calculations?
Yes. We carry out structural calculations in Wigan and the WN1, WN2, WN3, WN5 and WN6 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
What is a load take-down?
A load take-down is the part of the calculations that adds up every load reaching a beam or column and follows it down to the ground. It includes the roof, floors, walls, people, furniture and, where relevant, snow and wind. Each element along that path is then checked to make sure it can carry its share.
Can I use calculations from my architect or previous builder?
Yes, as long as they match what is actually being built. We check the spans, loads and bearing details against the layout and the site before ordering steel. If the plans have changed since the calculations were done, or the site differs from what was assumed, the engineer needs to update them first.
Do I need calculations for an old beam when selling my house?
Often a buyer's surveyor or solicitor will ask for them if there is no record of the beam being approved. An engineer can inspect the existing steel, check it against the loads and issue calculations or a report. In England and Wales these can support a regularisation application for retrospective approval.