Steel BeamInstallers
Corroded old steel beam exposed for replacement, with props and a new beam on trestles

Steel beam replacement & repair · Inverness

Steel beam replacement & repair in Inverness

Steel beam replacement & repair in Inverness, from free survey to completion certificate.

  • Survey, design and installation in one
  • Covering IV1, IV2, IV3
  • Inspected before it is covered

Free survey in Inverness

Tell us about the steel beam replacement & repair job in Inverness.

Please enter your name.
Please enter a UK phone number.
Please enter a valid email.
Please enter a UK postcode.
Please tell us a little about the job.
  • Free survey visit
  • Engineer's calculations arranged
  • Building control handled
  • Fixed written price once scope is agreed
  • England, Wales, mainland Scotland & NI

About our steel beam replacement & repair service in Inverness

If you live in Inverness, steel beam replacement & repair can usually be planned and priced after a single survey visit. The wider the Highlands area is covered as well. We cover IV1, IV2 and IV3, and we fix the price in writing once the layout and scope are agreed.

Not every steel beam was put in properly. Some were fitted decades ago without calculations, some sit on crumbling brick or timber packing, and some have rusted where water reached them through a leaking roof, a shopfront or a damp wall. Cracks in the plaster above, doors that stick or a visible dip are common warning signs.

Key points for your project

  • Beams fitted without calculations, whether decades ago or more recently without approval, may be smaller than the loads require, particularly in shop conversions and older knock-throughs. An engineer can check the existing section against the actual loads and say whether it is adequate.
  • Corrosion usually starts where water reaches the steel: under a leaking flat roof, behind a shopfront fascia, in a damp external wall or at a cellar ceiling. Light surface rust can often be cleaned and treated, while heavy loss of section changes the beam's strength.
  • A proper assessment means opening the boxing at the ends and along the span so the engineer can see the steel. In buildings from before 2000, old boxing can contain asbestos insulating board, so it is checked before anyone cuts into it.
  • Whether to strengthen or replace is the engineer's decision. Plating, where steel plates are fixed to the flanges, can add capacity without removing the beam, but it is not suitable for every section, connection or level of damage.
  • Shop beams over old shopfronts are a common repair job. They often carry the whole front wall of the upper floors, sit behind fascias where rain gets in, and may have been cut or altered when shopfronts were replaced in the past.

How the job runs in Inverness

  1. Free visit

    A short visit to Inverness to see the job, agree what you want and check the bearings, floors and services that affect the design.

  2. Calculations

    The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.

  3. Building warrant

    A building warrant is applied for from The Highland Council, and work starts only once the warrant has been granted.

  4. Steel in, made good

    On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.

How much should I budget in Inverness?

As a guide, budget £1,800–£5,000 including VAT for steel beam replacement in Inverness, based on published UK cost guides adjusted for prices in Scotland (-9%).

JobTypical guide rangeWhat it usually covers
Steel beam replacement£1,800–£5,000Propping, removing the failed beam, new steel on proper bearings, approval and making good
Fire protection to a steel beam£140–£550 per beamFire-rated board boxing or an intumescent coating system as specified
Shop or commercial structural opening£4,550–£13,650Transfer beam and columns for opening units together or forming a shopfront opening
Structural calculations for a beam£230–£680Site measure or photos, beam and padstone design and calculations for building standards

Figures include our approximate regional adjustment for prices in Scotland (-9%) and are rounded. How these figures are worked out.

Building control and neighbours in Inverness

Steel beam work in Inverness needs a building warrant from The Highland Council. The structural design is part of the application, and the council's building standards team accepts the completion certificate once the work is done as approved.

Scotland has no Party Wall Act. Work affecting a shared wall is governed by your title deeds and the general law, and in flats by the Tenements (Scotland) Act 2004, so it is sensible to agree the work with neighbours in writing before starting.

Building rules in Scotland

Steel beam replacement & repair near Inverness

Local questions answered

Do you cover Inverness for steel beam replacement & repair?

Yes. We carry out steel beam replacement & repair in Inverness and the IV1, IV2 and IV3 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.

What happens at the survey visit in Inverness?

We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.

Can a rusty steel beam be repaired?

Often, yes. Surface rust can usually be cleaned back to sound steel and treated with a protective coating. Where corrosion has eaten into the flanges or web, the engineer works out the remaining strength and decides whether plating will restore it or the beam needs replacing. The source of the moisture must be fixed as well.

Is it cheaper to repair or replace a steel beam?

Repair is often less disruptive and can cost less, but only when the engineer confirms it will do the job. Heavily corroded or badly undersized beams may need replacing anyway, and plating in awkward positions is not always cheaper. We price the option the engineer specifies in an itemised written quote.

What does it mean to plate a steel beam?

Plating means fixing extra steel plates to the beam, usually along the flanges, to increase its strength or stiffness without taking it out. The plates are bolted or welded according to the engineer's design. It suits some beams well, but not all, and the engineer checks the connections and bearings before specifying it.

Do you also work near Inverness?

Yes. We also cover nearby towns including Dingwall, Alness, Nairn and Aviemore.

Planning to take a wall out?

Book a free survey visit. You get an itemised written quote covering calculations, building control, steel and making good.