Steel beam replacement & repair · Bordon
Steel beam replacement & repair in Bordon
Steel beam replacement & repair in Bordon, from free survey to completion certificate.
- Free survey visit in Bordon
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Steel beam replacement & repair in Bordon: how it works
Planning steel beam replacement & repair in Bordon? Our team covers GU35 and the streets around them. We also work in nearby Basingstoke, roughly 14.2 miles away. You get one written quote for the calculations, approvals, propping, steel and making good.
We start with a survey visit, arrange an engineer's inspection, then carry out whatever repair the engineer specifies, from new bearings to strengthening or full replacement. We handle building control and the temporary propping, and you get an itemised written quote before anything starts.
Things to plan for
- Shop beams over old shopfronts are a common repair job. They often carry the whole front wall of the upper floors, sit behind fascias where rain gets in, and may have been cut or altered when shopfronts were replaced in the past.
- Older beams were often left with no fire protection or boxed in ordinary materials. When a beam is repaired or replaced, the fire protection is brought up to what the engineer and building control specify, commonly fire-rated plasterboard or intumescent paint.
- Many problem beams are not faulty steel at all but poor bearings. Ends resting on loose brick, timber offcuts or no padstone can crush the masonry beneath, and the beam then drops slightly and cracks the finishes above.
- A repair only lasts if the cause is dealt with too. A leaking roof, blocked gutter or bridged damp-proof course that rusted the beam needs fixing first, otherwise new protective coatings will break down in the same way.
- Missing paperwork for an old beam often surfaces when a house is being sold and the buyer's surveyor asks for calculations. An engineer's inspection, any remedial work and a regularisation or completion certificate together answer those questions.
Four stages, one team
Free visit
A short visit to Bordon to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
What does steel beam replacement & repair cost in Bordon?
As a guide, budget £2,250–£6,150 including VAT for steel beam replacement in Bordon, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steel beam replacement | £2,250–£6,150 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Fire protection to a steel beam | £170–£670 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| RSJ supply and fit (single beam) | £900–£2,800 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Temporary works and propping | £170–£560 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Bordon
For Bordon, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Steel beam replacement & repair near Bordon
- Farnham 7.5 mi
- Aldershot 10.2 mi
- Fleet 11.8 mi
- Godalming 11.8 mi
- Farnborough 13.3 mi
- Basingstoke 14.2 mi
Steel beam replacement & repair in Bordon: your questions
Do you cover Bordon for steel beam replacement & repair?
Yes. We carry out steel beam replacement & repair in Bordon and the GU35 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Can you work on older or listed homes in Bordon?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Can you replace a steel beam without taking the ceiling down?
Usually only part of the ceiling needs to come down. The boxing and a strip of ceiling either side of the beam are removed so props can go in and the old steel can come out. The rest of the room is protected, and the disturbed area is replastered to blend with the existing finish.
How long does it take to replace a steel beam?
Anything from a day or two to around a week on site, depending on what the engineer specifies. Rebuilding a crushed bearing can be quick, while cutting out an old beam and fitting a new one in a typical room takes longer. Plastering and redecoration follow once building control has inspected the new steel.
What does it mean to plate a steel beam?
Plating means fixing extra steel plates to the beam, usually along the flanges, to increase its strength or stiffness without taking it out. The plates are bolted or welded according to the engineer's design. It suits some beams well, but not all, and the engineer checks the connections and bearings before specifying it.