Steel beam replacement & repair · Manchester
Steel beam replacement & repair in Manchester
Steelwork, approvals and making good for steel beam replacement & repair in Manchester and nearby.
- Free survey visit in Manchester
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our steel beam replacement & repair service in Manchester
We cover steel beam replacement & repair in Manchester (M1, M2, M4) and the streets around it. We also cover the surrounding towns and villages in Greater Manchester. Each job is designed by a structural engineer and approved through local building control before work begins.
We start with a survey visit, arrange an engineer's inspection, then carry out whatever repair the engineer specifies, from new bearings to strengthening or full replacement. We handle building control and the temporary propping, and you get an itemised written quote before anything starts.
What to expect
- Many problem beams are not faulty steel at all but poor bearings. Ends resting on loose brick, timber offcuts or no padstone can crush the masonry beneath, and the beam then drops slightly and cracks the finishes above.
- Repairs are usually more contained than a new opening because the room layout stays the same. The main disruption is stripping the boxing, propping the floor above and the dust from cutting steel, with the ceiling and walls around the beam replastered afterwards.
- The full scope is sometimes clear only once the steel is exposed. We price the inspection and opening up first where needed, then provide an itemised quote for the repair the engineer specifies, so you are not committing to work before the problem is understood.
- A repair only lasts if the cause is dealt with too. A leaking roof, blocked gutter or bridged damp-proof course that rusted the beam needs fixing first, otherwise new protective coatings will break down in the same way.
- Shop beams over old shopfronts are a common repair job. They often carry the whole front wall of the upper floors, sit behind fascias where rain gets in, and may have been cut or altered when shopfronts were replaced in the past.
Four stages, one team
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
Guide prices for steel beam replacement & repair in Manchester
As a guide, budget £1,900–£5,300 including VAT for steel beam replacement in Manchester, based on published UK cost guides adjusted for prices in the North West (-4%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steel beam replacement | £1,900–£5,300 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Structural calculations for a beam | £240–£720 | Site measure or photos, beam and padstone design and calculations for building control |
| Shop or commercial structural opening | £4,800–£14,400 | Transfer beam and columns for opening units together or forming a shopfront opening |
| RSJ supply and fit (single beam) | £770–£2,400 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for prices in the North West (-4%) and are rounded. How these figures are worked out.
Building control and neighbours in Manchester
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Local questions answered
Do you also work near Manchester?
Yes. We also cover nearby towns including Salford, Failsworth, Droylsden and Stretford.
Can you work on older or listed homes in Manchester?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Can an old shop beam be replaced while the flat above is occupied?
Often, yes, with careful planning. The front wall and floors above are propped from inside the shop, and sometimes from outside, before the old beam is cut out. Occupants can often stay in if the engineer is satisfied with the propping, though there will be noise for a few days. Where the flat is separately owned, access and consents need agreeing in advance.
What does it mean to plate a steel beam?
Plating means fixing extra steel plates to the beam, usually along the flanges, to increase its strength or stiffness without taking it out. The plates are bolted or welded according to the engineer's design. It suits some beams well, but not all, and the engineer checks the connections and bearings before specifying it.
Is it cheaper to repair or replace a steel beam?
Repair is often less disruptive and can cost less, but only when the engineer confirms it will do the job. Heavily corroded or badly undersized beams may need replacing anyway, and plating in awkward positions is not always cheaper. We price the option the engineer specifies in an itemised written quote.
What happens at the survey visit in Manchester?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.