Steel beam replacement & repair · Aberdeen
Steel beam replacement & repair in Aberdeen
Survey, engineer's design and installation of steel beam replacement & repair anywhere in Aberdeen.
- Survey, design and installation in one
- Covering AB10, AB11, AB12, AB13
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What steel beam replacement & repair involves in Aberdeen
Steel beam replacement and repair means dealing with an existing beam that is corroded, sagging, undersized or poorly supported. A structural engineer inspects it and decides whether it can be repaired, strengthened with welded or bolted plates, given new bearings, or must be taken out and replaced, with the structure propped throughout.
Looking for steel beam replacement & repair in Aberdeen? We cover the whole area, from the centre out to the suburbs. Our teams handle the calculations, the building warrant, the propping and the steel itself, and leave the opening ready for plastering and decoration.
Key points for your project
- The full scope is sometimes clear only once the steel is exposed. We price the inspection and opening up first where needed, then provide an itemised quote for the repair the engineer specifies, so you are not committing to work before the problem is understood.
- Shop beams over old shopfronts are a common repair job. They often carry the whole front wall of the upper floors, sit behind fascias where rain gets in, and may have been cut or altered when shopfronts were replaced in the past.
- Corrosion usually starts where water reaches the steel: under a leaking flat roof, behind a shopfront fascia, in a damp external wall or at a cellar ceiling. Light surface rust can often be cleaned and treated, while heavy loss of section changes the beam's strength.
- Older beams were often left with no fire protection or boxed in ordinary materials. When a beam is repaired or replaced, the fire protection is brought up to what the engineer and building standards specify, commonly fire-rated plasterboard or intumescent paint.
- Many problem beams are not faulty steel at all but poor bearings. Ends resting on loose brick, timber offcuts or no padstone can crush the masonry beneath, and the beam then drops slightly and cracks the finishes above.
How the job runs in Aberdeen
Free visit
A short visit to Aberdeen to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building warrant
A building warrant is applied for from Aberdeen City Council, and work starts only once the warrant has been granted.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
How much should I budget in Aberdeen?
As a guide, budget £1,800–£5,000 including VAT for steel beam replacement in Aberdeen, based on published UK cost guides adjusted for prices in Scotland (-9%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steel beam replacement | £1,800–£5,000 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Temporary works and propping | £140–£460 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Building warrant fee | £215–£435 | Statutory fee set by the estimated value of the work: £215 up to £5,000, rising on a sliding scale (fees from 1 April 2026) |
| RSJ supply and fit (single beam) | £730–£2,280 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for prices in Scotland (-9%) and are rounded. How these figures are worked out.
Approvals in Aberdeen
Scottish rules are stricter on timing than in England: the building warrant must be in place before the wall is touched. We prepare the application with the engineer's calculations and submit it to Aberdeen City Council. The finished work is then certified and a completion certificate submitted for acceptance.
There is no party wall notice system in Scotland. Instead, check your title deeds and, for flats, the tenement management scheme, and talk to neighbours early if the beam bears into a shared wall.
More in Aberdeen
Local questions answered
How much does steel beam replacement & repair cost in Aberdeen?
As a guide, budget £1,800–£5,000 including VAT for steel beam replacement in Aberdeen, based on published UK cost guides adjusted for prices in Scotland (-9%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
Who approves steel beam replacement & repair in Aberdeen?
Structural work in Aberdeen needs a building warrant from Aberdeen City Council, granted before work starts. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
How do I know if my steel beam is failing?
Look for cracks spreading from the ends of the beam, a dip you can see along its length, sticking doors or sloping floors above, and rust stains coming through the boxing. These signs do not always mean the steel is failing, but they do mean an engineer should inspect it and find the cause.
What does it mean to plate a steel beam?
Plating means fixing extra steel plates to the beam, usually along the flanges, to increase its strength or stiffness without taking it out. The plates are bolted or welded according to the engineer's design. It suits some beams well, but not all, and the engineer checks the connections and bearings before specifying it.
Can an old shop beam be replaced while the flat above is occupied?
Often, yes, with careful planning. The front wall and floors above are propped from inside the shop, and sometimes from outside, before the old beam is cut out. Occupants can often stay in if the engineer is satisfied with the propping, though there will be noise for a few days. Where the flat is separately owned, access and consents need agreeing in advance.
Why has my steel beam sagged?
A beam usually sags because it is too small for the load, the load has increased since it was fitted, or its bearings have crushed or moved. Every beam bends slightly within design limits, but a visible dip or new cracking suggests something has changed. An engineer can measure it and identify the cause.
How soon can steel beam replacement & repair start in Aberdeen?
Start dates depend on the engineer's calculations, the building warrant and any agreement needed with neighbours. We give you a realistic timetable after the survey and keep you updated as each approval comes through.