Plastering & making good · Cheshire
Plastering & making good in Cheshire
Survey, engineer's design and installation of plastering & making good anywhere in Cheshire.
- Free survey visit in Cheshire
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What plastering & making good involves in Cheshire
Plastering and making good is the finishing work after a beam goes in or a wall comes out: boxing the steel, fixing corner beads, patching ceilings and wall ends, infilling the floor where the wall stood and skimming everything smooth. The aim is a room that looks as if the opening was always there, ready for paint.
We carry out plastering & making good throughout Cheshire, for homeowners, landlords and builders who need the structural part done properly. Coverage takes in Winsford, Warrington and Macclesfield and everywhere in between. You get an itemised written quote that shows the calculations, approvals, steel, labour and finishing as separate lines.
Worth knowing before you start
- Fire-rated plasterboard is used for boxing steel that needs fire protection, while standard or moisture-resistant board suits ordinary ceiling and wall repairs. Using the right board in each place avoids rework when building control inspects.
- A boxed beam usually leaves a downstand below the ceiling line. Where a flat ceiling is wanted, the beam has to be set up into the floor void during installation, so the finish needs deciding before the steel goes in, not after.
- Fresh plaster has to dry before it is painted. A thin skim over board in a warm, ventilated room often dries within a few days to a week, while backing coats and deeper repairs take longer. Painting too soon can cause peeling and patchy colour.
- Making good is easy to underestimate when budgeting. Removing a wall disturbs the ceiling, both wall ends and the floor, and props and needles leave their own marks, so the finishing work usually covers far more than the opening itself.
- Making good is the last chance to route cables neatly before surfaces close up. Sockets, switches and lights moved for the new layout are first-fixed before boarding, and pipes crossing the old wall line can run within the floor infill.
Four stages, one team
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
How much should I budget in Cheshire?
As a guide, budget £290–£1,150 including VAT for plastering and making good in Cheshire, based on published UK cost guides adjusted for prices in the North West (-4%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £290–£1,150 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Chimney breast removal (ground floor) | £1,450–£2,900 | Ground-floor breast removed, steel to support the breast above, building control and making good |
| Fire protection to a steel beam | £140–£580 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Kitchen-diner knock-through | £2,400–£5,750 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
Figures include our approximate regional adjustment for prices in the North West (-4%) and are rounded. How these figures are worked out.
Approvals in Cheshire
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Plastering & making good by town
Plastering & making good in Cheshire: your questions
Can I stay at home while the work is done in Cheshire?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
What happens at the survey visit in Cheshire?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Can you repair a lath and plaster ceiling?
Yes. Small areas can be patched with lath and lime-based plaster, or with board cut in and skimmed to match. Where large areas have sagged or pulled away from the laths, overboarding or replacing the ceiling is often the sounder repair. We assess the condition at the survey and price the right approach.
Will cracks appear after plastering?
Small hairline cracks can appear in the first months as the plaster dries and the building settles onto the new steel. They are cosmetic and normal, and are usually filled when you next repaint. Wide or growing cracks are different and should be reported, as they can point to movement that needs checking.
Do you replace skirting boards and door frames after a knock-through?
Yes, where the work affects them. Skirting is extended or replaced so it runs through the new opening, and door linings and architraves are refitted or replaced where an opening has changed. Where period mouldings are involved, matching profiles can usually be sourced or made up to suit.
Do you decorate after making good?
Not usually. Making good leaves surfaces skimmed, dry and ready for paint, with trims refitted, and decoration is normally left to you or your decorator so you can choose colours and finishes yourself. Whoever paints should start with a thinned mist coat on the new plaster before the main coats.
Do you cover Cheshire for plastering & making good?
Yes. We carry out plastering & making good in Cheshire. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.