Plastering & making good · Crowthorne
Plastering & making good in Crowthorne
Plastering & making good for homes in RG40, RG45, designed by a structural engineer.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Crowthorne and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our plastering & making good service in Crowthorne
For homes in Crowthorne and the RG40 and RG45 districts, we handle plastering & making good from survey to sign-off. It sits about 9.7 miles from Reading, which we also cover. The beam is sized by a structural engineer and inspected before it is boxed in.
Structural work leaves a trail behind it: a steel beam to hide, ragged wall ends, a strip of missing floor, cracked ceiling where props stood and holes where needles passed through. However good the steel, this is the part you look at every day, so it deserves the same care as the structure.
Key points for your project
- A boxed beam usually leaves a downstand below the ceiling line. Where a flat ceiling is wanted, the beam has to be set up into the floor void during installation, so the finish needs deciding before the steel goes in, not after.
- Textured ceiling coatings applied before 2000 can contain asbestos. Before a textured ceiling is cut, scraped or sanded, a sample is tested or an asbestos survey of the area is arranged, and the finish is only disturbed once the result is known.
- Fresh plaster has to dry before it is painted. A thin skim over board in a warm, ventilated room often dries within a few days to a week, while backing coats and deeper repairs take longer. Painting too soon can cause peeling and patchy colour.
- Fire-rated plasterboard is used for boxing steel that needs fire protection, while standard or moisture-resistant board suits ordinary ceiling and wall repairs. Using the right board in each place avoids rework when building control inspects.
- When a wall is removed, a strip of floor goes with it. On suspended timber floors the gap is joisted and boarded, and on solid floors it is filled and screeded. Either way, the infill must sit level so new flooring does not show a ridge.
Four stages, one team
Survey in Crowthorne
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to Wokingham Borough Council, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
What does plastering & making good cost in Crowthorne?
As a guide, budget £340–£1,340 including VAT for plastering and making good in Crowthorne, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Plastering and making good | £340–£1,340 | Boxing the beam, bead and skim, reveals, floor infill where the wall stood and tidy-up |
| Load-bearing wall removal with steel beam | £2,250–£5,600 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Fire protection to a steel beam | £170–£670 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Through-lounge knock-through | £2,800–£6,150 | Wall between front and back reception rooms, steel beam, approvals, plastering and floor infill |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Approvals in Crowthorne
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either Wokingham Borough Council or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Local questions answered
Can you work on older or listed homes in Crowthorne?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
How soon can plastering & making good start in Crowthorne?
Start dates depend on the engineer's calculations, the building control approval and, where needed, party wall notice periods. We give you a realistic timetable after the survey and keep you updated as each approval comes through.
Is plastering included when a load-bearing wall is removed?
Yes, on our structural jobs making good is priced as part of the work and itemised on the written quote, so you can see exactly what is included. If another firm is doing the steelwork, check their quote closely, as some stop at the beam and leave plastering, floor infill and skirting for you to arrange.
Do you replace skirting boards and door frames after a knock-through?
Yes, where the work affects them. Skirting is extended or replaced so it runs through the new opening, and door linings and architraves are refitted or replaced where an opening has changed. Where period mouldings are involved, matching profiles can usually be sourced or made up to suit.
Can you match my old textured ceiling?
Often, yes, although a perfect match is hard over large patches. Before anything is touched, a textured coating applied before 2000 is tested for asbestos. Small areas can then be re-textured to blend in, while many people choose to skim the whole ceiling flat for a cleaner, consistent finish.
What happens at the survey visit in Crowthorne?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.