Loft conversion steels · Wiltshire
Loft conversion steels in Wiltshire
Loft conversion steels across Wiltshire, designed by a structural engineer and signed off by building control.
- Free survey visit in Wiltshire
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our loft conversion steels service in Wiltshire
Loft conversion steels are the beams that let a roof space become a usable room. They carry the new floor so it does not rest on the old ceiling joists, support the roof where purlins and struts are removed or rafters are cut for a dormer, and bear onto padstones in the gable or party walls as a structural engineer specifies.
Loft conversion steels in Wiltshire follows the same careful process wherever the property is: a survey, an engineer's design, the right approval and safe temporary works. We work in Trowbridge, Chippenham and Salisbury and the surrounding villages. We price it all up front so there are no surprises once the wall is open.
Things to plan for
- Many later twentieth-century homes have trussed rafter roofs, with diagonal timbers running through the whole loft. Converting these involves more steel and new timber, because each truss is cut and its load has to be re-routed by design.
- In older terraces the party wall at loft level can be thin, built in soft brick, or contain old chimney flues. The engineer may avoid bearing over a flue, ask for a section of wall to be rebuilt, or use a post down to firmer support.
- The steel stage of a loft conversion usually takes a few working days and comes early, before floor joists, dormer framing and insulation. Keep the steel calculations with the completion certificate, as both are asked for when the house is sold.
- Cutting pockets into a party wall for steel bearings is notifiable work in England and Wales under the Party Wall etc. Act 1996. A party structure notice must be served at least two months before that work starts, so it is worth raising early in the planning.
- Traditional cut roofs rely on purlins and struts running down to internal walls. A steel beam can take over that job so the struts come out, freeing up floor and headroom, but the change has to be designed and propped carefully.
Four stages, one team
Free visit
A short visit to Wiltshire to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
Guide prices for loft conversion steels in Wiltshire
As a guide, budget £2,600–£6,200 including VAT for loft conversion steels in Wiltshire, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Loft conversion steels | £2,600–£6,200 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Party wall surveyor (agreed surveyor, per neighbour) | £930–£2,060 per neighbour | Schedule of condition and award where a neighbour dissents; serving notice alone, where the neighbour consents, costs far less (England and Wales only) |
| Structural calculations for a beam | £260–£770 | Site measure or photos, beam and padstone design and calculations for building control |
| Temporary works and propping | £150–£520 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Building control and neighbours in Wiltshire
For Wiltshire, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Loft conversion steels by town
Local questions answered
What happens at the survey visit in Wiltshire?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Which towns in Wiltshire do you cover?
We cover towns including Swindon, Salisbury, Trowbridge and Chippenham, plus the villages and smaller towns around them.
Do all loft conversions need steel beams?
Most do, but not all. Steels are usually needed to carry the new floor, replace purlins and struts, or support the roof around a dormer. Some smaller conversions use deeper timber joists or engineered timber instead. A structural engineer decides what the roof and walls need after a survey.
Can I stay in my house during a loft conversion?
Usually, yes. Most of the steel work happens in the roof space, with access through the loft hatch or a roof opening, so the rest of the house stays usable. Expect noise while pockets are cut into the walls and some dust on the landing, which is screened off.
Do I need building regulations for loft conversion steels?
Yes. Loft conversions are building work, and the steels form part of the structural design checked by building control in England, Wales and Northern Ireland. In Scotland a building warrant must be granted before work begins. The inspector checks the steel bearings before they are covered up.
How do you get steel beams into a loft?
It depends on access. Beams are often passed in through an opening made in the roof or a gable window, or brought up in shorter sections and bolted together in the loft where the engineer's design allows. For long or heavy steels a hoist or crane may be used, planned in advance.