Load-bearing wall removal · Worthing
Load-bearing wall removal in Worthing
Steelwork, approvals and making good for load-bearing wall removal in Worthing and nearby.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Worthing and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning load-bearing wall removal in Worthing
For homes in Worthing and the BN11, BN12, BN13, BN14 and BN15 districts, we handle load-bearing wall removal from survey to sign-off. Worthing is around 10.3 miles from Brighton, and we cover both. The beam is sized by a structural engineer and inspected before it is boxed in.
We handle the whole job: a survey visit, structural calculations from a qualified engineer, building control, temporary propping, the steel itself, and making good afterwards. You get one itemised written quote and one team to deal with from first visit to sign-off.
Key points for your project
- Expect some dust and noise for a day or two while the wall comes out. We screen the work area, protect floors and sweep up daily, and the rest of the house usually stays usable throughout.
- Cables, pipes, radiators and sometimes gas runs pass through internal walls. These are traced at the survey so they can be rerouted by the right trade before or during the work, not discovered halfway through.
- Whether a wall is load-bearing is not always obvious. Joists running across the wall, a wall directly above, or the wall sitting on a footing in the floor are common clues, but the engineer's check on site is what settles it.
- The finished opening should be signed off with a completion certificate from building control. Keep it with your house documents, as solicitors ask for it when the property is sold.
- Each end of the beam needs a solid bearing. Padstones spread the point load into the masonry below, and if the wall underneath is weak the engineer may call for a steel column or a new pad foundation instead.
What happens, step by step
Survey in Worthing
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for load-bearing wall removal in Worthing
As a guide, budget £2,250–£5,600 including VAT for load-bearing wall removal with steel beam in Worthing, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Load-bearing wall removal with steel beam | £2,250–£5,600 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Temporary works and propping | £170–£560 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Kitchen-diner knock-through | £2,800–£6,700 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| RSJ supply and fit (single beam) | £900–£2,800 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Worthing
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Load-bearing wall removal near Worthing
- Portslade 7.2 mi
- Littlehampton 7.2 mi
- Hove 9.1 mi
- Brighton 10.3 mi
- Bognor Regis 13.5 mi
- Rottingdean 13.8 mi
Local questions answered
Do you also work near Worthing?
Yes. We also cover nearby towns including Portslade, Littlehampton, Hove and Brighton.
Who sizes the steel beam?
A structural engineer. They look at the span, the loads from floors, walls and roof above, and the bearings at each end, then specify the beam, padstones and any columns. We arrange those calculations, or work to calculations you already have.
What happens if the wall is shared with my neighbour?
In England and Wales, cutting into a party wall to take the end of a beam is covered by the Party Wall etc. Act 1996, and notice must be served on the neighbour before work starts. Scotland and Northern Ireland have no equivalent Act, so the title deeds and the general law apply instead.
Can I stay in the house while the wall is removed?
In most cases yes. The work area is screened, floors are protected and the house stays usable, though the rooms either side of the wall will be out of action for a few days and there will be some noise and dust.