Load-bearing wall removal · Reigate
Load-bearing wall removal in Reigate
Steelwork, approvals and making good for load-bearing wall removal in Reigate and nearby.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Reigate and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Load-bearing wall removal in Reigate: how it works
If you live in Reigate, load-bearing wall removal can usually be planned and priced after a single survey visit. Reigate is around 8.6 miles from Crawley, and we cover both. We cover RH1 and RH2, and we fix the price in writing once the layout and scope are agreed.
We handle the whole job: a survey visit, structural calculations from a qualified engineer, building control, temporary propping, the steel itself, and making good afterwards. You get one itemised written quote and one team to deal with from first visit to sign-off.
Worth knowing before you start
- Most single-wall removals in a typical house take two to five working days on site for the structural part. Plastering, drying out and decorating follow on, and building control visits fit around those stages.
- Building control is needed because removing a structural wall is controlled building work. Doing it without approval can cause problems when you come to sell, and putting it right afterwards costs far more than doing it properly first time.
- Temporary works matter as much as the beam. Props, spreaders and needles carry the house while the wall is out, and they are positioned so the floor below can take them too.
- Homes built before 2000 may contain asbestos in textured ceilings, boxing or old boards. Where there is a risk, a survey of the area being disturbed is arranged before the wall comes out.
- Expect some dust and noise for a day or two while the wall comes out. We screen the work area, protect floors and sweep up daily, and the rest of the house usually stays usable throughout.
How the job runs in Reigate
Survey in Reigate
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Reigate?
As a guide, budget £2,250–£5,600 including VAT for load-bearing wall removal with steel beam in Reigate, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Load-bearing wall removal with steel beam | £2,250–£5,600 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Kitchen-diner knock-through | £2,800–£6,700 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| Temporary works and propping | £170–£560 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| Structural calculations for a beam | £280–£840 | Site measure or photos, beam and padstone design and calculations for building control |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Approvals in Reigate
For Reigate, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Load-bearing wall removal in Reigate: your questions
Do you cover Reigate for load-bearing wall removal?
Yes. We carry out load-bearing wall removal in Reigate and the RH1 and RH2 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Can I stay at home while the work is done in Reigate?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Who sizes the steel beam?
A structural engineer. They look at the span, the loads from floors, walls and roof above, and the bearings at each end, then specify the beam, padstones and any columns. We arrange those calculations, or work to calculations you already have.
How long does it take to remove a load-bearing wall?
For a typical house the structural part usually takes two to five working days: propping, taking the wall out, fitting the steel and packing it tight. Plastering and decorating follow once building control has inspected the steel.
Do I need planning permission to remove an internal wall?
Usually not, because internal alterations to a house are not normally development needing planning permission. Listed buildings are different and need listed building consent, and flats normally need the freeholder's or landlord's written consent.
Do I need a party wall agreement for load-bearing wall removal in Reigate?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.