Load-bearing wall removal · Folkestone
Load-bearing wall removal in Folkestone
Steelwork, approvals and making good for load-bearing wall removal in Folkestone and nearby.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our load-bearing wall removal service in Folkestone
We carry out load-bearing wall removal in Folkestone, covering the CT18, CT19 and CT20 postcode districts. We also cover the surrounding towns and villages in Kent. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
We handle the whole job: a survey visit, structural calculations from a qualified engineer, building control, temporary propping, the steel itself, and making good afterwards. You get one itemised written quote and one team to deal with from first visit to sign-off.
What to expect
- Homes built before 2000 may contain asbestos in textured ceilings, boxing or old boards. Where there is a risk, a survey of the area being disturbed is arranged before the wall comes out.
- If the wall carries a chimney breast, a wall upstairs and floor joists all at once, the engineer may specify a heavier beam or two beams side by side. The quote reflects that once calculations are back.
- Each end of the beam needs a solid bearing. Padstones spread the point load into the masonry below, and if the wall underneath is weak the engineer may call for a steel column or a new pad foundation instead.
- Cables, pipes, radiators and sometimes gas runs pass through internal walls. These are traced at the survey so they can be rerouted by the right trade before or during the work, not discovered halfway through.
- Building control is needed because removing a structural wall is controlled building work. Doing it without approval can cause problems when you come to sell, and putting it right afterwards costs far more than doing it properly first time.
What happens, step by step
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
What does load-bearing wall removal cost in Folkestone?
As a guide, budget £2,250–£5,600 including VAT for load-bearing wall removal with steel beam in Folkestone, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Load-bearing wall removal with steel beam | £2,250–£5,600 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Temporary works and propping | £170–£560 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
| RSJ supply and fit (single beam) | £900–£2,800 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Through-lounge knock-through | £2,800–£6,150 | Wall between front and back reception rooms, steel beam, approvals, plastering and floor infill |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Folkestone
For Folkestone, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Load-bearing wall removal in Folkestone: your questions
Can I stay at home while the work is done in Folkestone?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Do you also work near Folkestone?
Yes. We also cover nearby towns including Dover, Ashford, Deal and Canterbury.
Who sizes the steel beam?
A structural engineer. They look at the span, the loads from floors, walls and roof above, and the bearings at each end, then specify the beam, padstones and any columns. We arrange those calculations, or work to calculations you already have.
Do I need building regulations approval to remove a load-bearing wall?
Yes. In England removing a structural wall is building work that needs building control approval, through a full plans application or a building notice. In Wales it needs an application under the Welsh regulations. In Scotland it needs a building warrant before work starts, and in Northern Ireland the council's building control must receive a full plans application or, for an existing single dwelling, a building notice before work starts. We arrange this as part of the job.
What happens if the wall is shared with my neighbour?
In England and Wales, cutting into a party wall to take the end of a beam is covered by the Party Wall etc. Act 1996, and notice must be served on the neighbour before work starts. Scotland and Northern Ireland have no equivalent Act, so the title deeds and the general law apply instead.