Load-bearing wall removal · Cardiff
Load-bearing wall removal in Cardiff
Survey, engineer's design and installation of load-bearing wall removal anywhere in Cardiff.
- Survey, design and installation in one
- Covering CF10, CF11, CF14, CF15
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning load-bearing wall removal in Cardiff
Load-bearing wall removal means taking out a wall that holds up floors, roof loads or walls above it, and replacing that support with a steel beam sized by a structural engineer. The beam sits on padstones at each end, the weight above is held on temporary props while the wall comes out, and building control inspects the finished work.
We carry out load-bearing wall removal throughout Cardiff, for homeowners, landlords and builders who need the structural part done properly. That covers every postcode district in the area. You get an itemised written quote that shows the calculations, approvals, steel, labour and finishing as separate lines.
Key points for your project
- Each end of the beam needs a solid bearing. Padstones spread the point load into the masonry below, and if the wall underneath is weak the engineer may call for a steel column or a new pad foundation instead.
- Homes built before 2000 may contain asbestos in textured ceilings, boxing or old boards. Where there is a risk, a survey of the area being disturbed is arranged before the wall comes out.
- The finished opening should be signed off with a completion certificate from building control. Keep it with your house documents, as solicitors ask for it when the property is sold.
- Older homes can hide surprises such as weak lime mortar, timber lintels or a wall with no proper footing. Where the engineer needs something extra, we price it before any work starts rather than after.
- Cables, pipes, radiators and sometimes gas runs pass through internal walls. These are traced at the survey so they can be rerouted by the right trade before or during the work, not discovered halfway through.
Four stages, one team
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit the application or notice to Cardiff Council under the Building Regulations as they apply in Wales, before work starts.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
What does load-bearing wall removal cost in Cardiff?
As a guide, budget £1,800–£4,550 including VAT for load-bearing wall removal with steel beam in Cardiff, based on published UK cost guides adjusted for prices in Wales (-9%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Load-bearing wall removal with steel beam | £1,800–£4,550 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Building control fees | £230–£590 | Application fee and inspections under the Welsh building regulations; varies by council or approver |
| RSJ supply and fit (single beam) | £730–£2,280 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Temporary works and propping | £140–£460 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in Wales (-9%) and are rounded. How these figures are worked out.
Building rules for Cardiff
In Wales, structural alterations come under the Building Regulations 2010 as they apply in Wales. Cardiff Council handles building control for Cardiff. For work started or approved from 1 July 2026, the Welsh system uses an application to building control, dutyholders appointed in writing, a commencement notice before work starts and a compliance statement at the end.
The Party Wall etc. Act 1996 applies in Wales as well as England, so a beam bearing into a shared wall needs a party structure notice at least two months before work starts. We arrange notices through a party wall surveyor.
More in Cardiff
Local questions answered
What happens at the survey visit in Cardiff?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Can you work on older or listed homes in Cardiff?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
How do I know if my wall is load-bearing?
Clues include floor joists that run across the top of the wall, a wall directly above it upstairs, and a wall that is solid brick or block rather than a hollow stud partition. None of these is proof on its own. A structural engineer checks on site and confirms it before any work is planned.
Who sizes the steel beam?
A structural engineer. They look at the span, the loads from floors, walls and roof above, and the bearings at each end, then specify the beam, padstones and any columns. We arrange those calculations, or work to calculations you already have.
Can I stay in the house while the wall is removed?
In most cases yes. The work area is screened, floors are protected and the house stays usable, though the rooms either side of the wall will be out of action for a few days and there will be some noise and dust.
Will the beam show once the job is finished?
It depends on the design. Most beams sit just below the ceiling and are boxed in with plasterboard, leaving a small step. A beam can be set up into the floor void for a flat ceiling, which takes more work, or left exposed and painted where you want an industrial look.
How soon can load-bearing wall removal start in Cardiff?
Start dates depend on the engineer's calculations, the building control approval and, where needed, party wall notice periods. We give you a realistic timetable after the survey and keep you updated as each approval comes through.