Garage conversion openings · Richmond
Garage conversion openings in Richmond
Steelwork, approvals and making good for garage conversion openings in Richmond and nearby.
- Free survey visit in Richmond
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our garage conversion openings service in Richmond
If you live in Richmond, garage conversion openings can usually be planned and priced after a single survey visit. We also cover the surrounding towns and villages in London. We cover SW14, TW1, TW2, TW3 and TW7, and we fix the price in writing once the layout and scope are agreed.
For integral garages with a bedroom above, the beam over the garage door matters even more, because it carries the front wall of the room upstairs. We arrange the survey visit, engineer's calculations, building control, propping, any steel and making good, with the structural items set out in one itemised written quote.
Key points for your project
- Garage floors often sit lower than the house floor and may have no damp-proof membrane. The infill wall needs a damp-proof course linked to the existing walls, and the floor usually needs a membrane, insulation and screed raised to the house level.
- An infill wall needs a proper foundation. Garage floors are often a thin slab with no footing under the door line, so a new trench footing is usually dug across the opening to a depth and width the engineer and building control agree.
- Most garage conversions do not need planning permission, but some estates have conditions removing permitted development rights for garages, and listed buildings or flats need consent. Changing the front elevation can also need permission in some areas.
- Garages built before 2000 can contain asbestos cement in roof sheets, wall panels or the garage door itself. A survey of the materials being disturbed is needed before work starts, so any asbestos can be removed or managed correctly.
- The beam or lintel over a garage door was designed to span an open gap. It may be timber, concrete or steel, and in older houses it can be undersized or corroded, so the engineer checks it before anything is built underneath or above it.
Four stages, one team
Free visit
A short visit to Richmond to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
Guide prices for garage conversion openings in Richmond
As a guide, budget £1,300–£3,850 including VAT for garage door opening infill (structural part) in Richmond, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Garage door opening infill (structural part) | £1,300–£3,850 | Beam or lintel checked or replaced, foundation and infill wall for the old door opening (window and finishes extra) |
| Lintel replacement | £510–£1,540 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
| RSJ supply and fit (single beam) | £1,000–£3,200 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Structural calculations for a beam | £320–£960 | Site measure or photos, beam and padstone design and calculations for building control |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building control and neighbours in Richmond
For Richmond, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Garage conversion openings in Richmond: your questions
Do I need a party wall agreement for garage conversion openings in Richmond?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
Can I stay at home while the work is done in Richmond?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Do I need planning permission to convert my garage?
Often not, because a garage conversion is largely internal work within permitted development. However, some newer estates have planning conditions that remove permitted development rights for garages, and listed buildings, flats and some front elevation changes need consent. Check your property's planning history with the council before committing.
Can I knock through from my garage into the kitchen?
Usually, yes. The wall between an attached or integral garage and the house is often load-bearing, so the opening needs a lintel or steel beam designed by a structural engineer and approved by building control. If any of the garage stays as storage, the opening needs fire separation, such as a fire door.
Does the infill wall need foundations?
Yes. A new masonry wall across the garage door opening needs a proper footing, as the existing garage slab is usually not designed to carry it. A trench is dug across the opening and a foundation is formed to the engineer's and building control's requirements, then inspected before the wall is built.
What happens at the survey visit in Richmond?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.