Flat & HMO conversion steels · Fulham
Flat & HMO conversion steels in Fulham
Flat & HMO conversion steels in Fulham, from free survey to completion certificate.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Fulham and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our flat & HMO conversion steels service in Fulham
Fulham has a mix of housing, and flat & HMO conversion steels need a slightly different approach in each. The wider London area is covered as well. Whatever the age of the property, the steel goes in on proper bearings with temporary support in place throughout.
Turning a large house into flats or an HMO rarely leaves every wall where it was. Rooms are split and joined, kitchens and bathrooms appear on upper floors, and new stairs or corridors are formed. Each time a load-bearing wall moves, steel usually takes its place, and it has to suit the fire and sound standards of a building shared by several households.
Worth knowing before you start
- Separating floors and walls also have to meet sound insulation standards. Steel connections and boxing are detailed so they do not leave gaps or rigid paths for noise, and sound testing near completion checks that the separating construction performs.
- Many HMOs need a licence from the local council, with conditions covering room sizes, shared facilities and fire safety. Licensing runs alongside building regulations rather than replacing them, so the layout and steelwork should suit both from the outset.
- The engineer looks at the whole building rather than one opening at a time. Loads from upper floors, new bathrooms and water storage are traced down to the foundations, and steel is placed so it suits the new layout without awkward downstands in habitable rooms.
- Floors and walls between flats must resist the spread of fire, and steel holding up those floors needs protection to match. Where a beam passes through a separating wall or floor, the gaps around it are fire-stopped so the separation stays continuous.
- A conversion to flats or an HMO may need planning permission for the change of use, depending on the scheme, its size and any local restrictions. Checking the planning position before design work begins avoids redesigning the layout and its steel later.
How the job runs in Fulham
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
Guide prices for flat & HMO conversion steels in Fulham
As a guide, budget £3,200–£11,500 including VAT for steelwork for a flat or HMO conversion in Fulham, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steelwork for a flat or HMO conversion | £3,200–£11,500 | Beams and posts for a revised layout, with approvals; fire and sound separation priced with the conversion |
| Steel column or post | £640–£1,920 per column | Column supplied and fitted with base and cap plates on a pad foundation |
| Fire protection to a steel beam | £190–£770 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Structural calculations for a beam | £320–£960 | Site measure or photos, beam and padstone design and calculations for building control |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building rules for Fulham
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Flat & HMO conversion steels near Fulham
- Chelsea 1.4 mi
- Putney 1.6 mi
- Battersea 1.9 mi
- Shepherds Bush 1.9 mi
- Barnes 2.2 mi
- Notting Hill 2.2 mi
Questions about flat & HMO conversion steels in Fulham
Can you work on older or listed homes in Fulham?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Do you cover Fulham for flat & HMO conversion steels?
Yes. We carry out flat & HMO conversion steels in Fulham and the SW3, SW5, SW6, SW7 and SW10 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
How is sound insulation handled around steel beams in flats?
Through careful detailing. Separating floors and walls between flats must meet sound insulation standards, so steel connections, boxing and packing are designed not to leave gaps or create direct paths for noise. In England and Wales, sound testing is normally carried out on conversions before completion to show the separating construction performs.
Can you install the steel while my main contractor runs the conversion?
Yes. On many conversions the steelwork is installed as a package within a wider build, working to the main contractor's programme and the engineer's design. We coordinate propping, deliveries and building control inspections for the steel so the other trades can follow on smoothly once it is in.
Do I need an HMO licence before converting a house?
Possibly. Many HMOs need a licence from the local council, and some areas license smaller HMOs too. Licensing covers room sizes, amenities and fire safety, and it is separate from planning and building regulations. Check the council's requirements early, as they can affect the layout and therefore the steelwork needed.
Can I stay at home while the work is done in Fulham?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.