Flat & HMO conversion steels · Bordon
Flat & HMO conversion steels in Bordon
Flat & HMO conversion steels in Bordon, from free survey to completion certificate.
- Free survey visit in Bordon
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning flat & HMO conversion steels in Bordon
Bordon has a mix of housing, and flat & HMO conversion steels need a slightly different approach in each. We also work in nearby Basingstoke, roughly 14.2 miles away. Whatever the age of the property, the steel goes in on proper bearings with temporary support in place throughout.
Turning a large house into flats or an HMO rarely leaves every wall where it was. Rooms are split and joined, kitchens and bathrooms appear on upper floors, and new stairs or corridors are formed. Each time a load-bearing wall moves, steel usually takes its place, and it has to suit the fire and sound standards of a building shared by several households.
Worth knowing before you start
- A conversion to flats or an HMO may need planning permission for the change of use, depending on the scheme, its size and any local restrictions. Checking the planning position before design work begins avoids redesigning the layout and its steel later.
- Floors and walls between flats must resist the spread of fire, and steel holding up those floors needs protection to match. Where a beam passes through a separating wall or floor, the gaps around it are fire-stopped so the separation stays continuous.
- In a conversion, walls that carried load are often taken out to form open kitchens or wider corridors, while new partitions go in elsewhere. Each change is checked, because a new stud wall standing on old joists can add load the floor was never designed for.
- The reduced 5% rate of VAT may apply to some conversion work, such as changing the number of dwellings in a building. Whether it applies depends on the details of the scheme, so confirm the position with your accountant before relying on it.
- The engineer looks at the whole building rather than one opening at a time. Loads from upper floors, new bathrooms and water storage are traced down to the foundations, and steel is placed so it suits the new layout without awkward downstands in habitable rooms.
Four stages, one team
Survey in Bordon
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for flat & HMO conversion steels in Bordon
As a guide, budget £2,800–£10,100 including VAT for steelwork for a flat or HMO conversion in Bordon, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steelwork for a flat or HMO conversion | £2,800–£10,100 | Beams and posts for a revised layout, with approvals; fire and sound separation priced with the conversion |
| Fire protection to a steel beam | £170–£670 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Structural calculations for a beam | £280–£840 | Site measure or photos, beam and padstone design and calculations for building control |
| Load-bearing wall removal with steel beam | £2,250–£5,600 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Bordon
For Bordon, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Flat & HMO conversion steels near Bordon
- Farnham 7.5 mi
- Aldershot 10.2 mi
- Fleet 11.8 mi
- Godalming 11.8 mi
- Farnborough 13.3 mi
- Basingstoke 14.2 mi
Flat & HMO conversion steels in Bordon: your questions
What happens at the survey visit in Bordon?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Do you cover Bordon for flat & HMO conversion steels?
Yes. We carry out flat & HMO conversion steels in Bordon and the GU35 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Do I need building regulations to convert a house into flats?
Yes. Converting a house into flats is a material change of use, so the building has to meet requirements for fire safety, sound insulation, structure and other matters. In England and Wales that means a building control application, in Scotland a building warrant before work starts, and in Northern Ireland an application to council building control.
Do I need an HMO licence before converting a house?
Possibly. Many HMOs need a licence from the local council, and some areas license smaller HMOs too. Licensing covers room sizes, amenities and fire safety, and it is separate from planning and building regulations. Check the council's requirements early, as they can affect the layout and therefore the steelwork needed.
Does 5% VAT apply to a flat conversion?
It may. A reduced rate of VAT can apply to some conversion work, such as changing the number of dwellings in a building or converting a house into an HMO, provided the conditions are met. The rules have detail and exceptions, so confirm the position with your accountant before pricing the project on that basis.
Can you work on older or listed homes in Bordon?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.