Flat & HMO conversion steels · Hove
Flat & HMO conversion steels in Hove
Flat & HMO conversion steels for homes in BN1, BN2, BN3, designed by a structural engineer.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Flat & HMO conversion steels in Hove: how it works
We carry out flat & HMO conversion steels in Hove, covering the BN1, BN2, BN3 and BN41 postcode districts. We also work in nearby Brighton, roughly 1.2 miles away. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
Turning a large house into flats or an HMO rarely leaves every wall where it was. Rooms are split and joined, kitchens and bathrooms appear on upper floors, and new stairs or corridors are formed. Each time a load-bearing wall moves, steel usually takes its place, and it has to suit the fire and sound standards of a building shared by several households.
Key points for your project
- Converting a house into flats is treated as a material change of use for building regulations purposes, so fire safety, sound insulation and other requirements apply across the building, not just to the structural work. The steelwork forms one part of that wider approval.
- Steelwork is usually one of the first structural stages in a conversion. Getting beams in, inspected and fire protected early lets partitions, services and separating construction follow on, so any delay to the steel tends to hold up every trade after it.
- Floors and walls between flats must resist the spread of fire, and steel holding up those floors needs protection to match. Where a beam passes through a separating wall or floor, the gaps around it are fire-stopped so the separation stays continuous.
- Separating floors and walls also have to meet sound insulation standards. Steel connections and boxing are detailed so they do not leave gaps or rigid paths for noise, and sound testing near completion checks that the separating construction performs.
- Many HMOs need a licence from the local council, with conditions covering room sizes, shared facilities and fire safety. Licensing runs alongside building regulations rather than replacing them, so the layout and steelwork should suit both from the outset.
Four stages, one team
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to Brighton & Hove City Council, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
Guide prices for flat & HMO conversion steels in Hove
As a guide, budget £2,800–£10,100 including VAT for steelwork for a flat or HMO conversion in Hove, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Steelwork for a flat or HMO conversion | £2,800–£10,100 | Beams and posts for a revised layout, with approvals; fire and sound separation priced with the conversion |
| Loft conversion steels | £2,800–£6,700 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
| Structural calculations for a beam | £280–£840 | Site measure or photos, beam and padstone design and calculations for building control |
| Load-bearing wall removal with steel beam | £2,250–£5,600 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Hove
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either Brighton & Hove City Council or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Flat & HMO conversion steels near Hove
- Brighton 1.2 mi
- Portslade 2.3 mi
- Rottingdean 4.9 mi
- Burgess Hill 8.9 mi
- Worthing 9.1 mi
- Haywards Heath 11.9 mi
Local questions answered
Do you also work near Hove?
Yes. We also cover nearby towns including Brighton, Portslade, Rottingdean and Burgess Hill.
Who approves flat & HMO conversion steels in Hove?
Structural work in Hove needs a building notice or full plans application to Brighton & Hove City Council or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Does 5% VAT apply to a flat conversion?
It may. A reduced rate of VAT can apply to some conversion work, such as changing the number of dwellings in a building or converting a house into an HMO, provided the conditions are met. The rules have detail and exceptions, so confirm the position with your accountant before pricing the project on that basis.
Can you install the steel while my main contractor runs the conversion?
Yes. On many conversions the steelwork is installed as a package within a wider build, working to the main contractor's programme and the engineer's design. We coordinate propping, deliveries and building control inspections for the steel so the other trades can follow on smoothly once it is in.
How long does the steelwork take on a house-to-flats conversion?
Typically one to three weeks on site, depending on how many walls move and how the work is phased. The steel is usually among the first structural stages, so it is programmed early to let partitions, services and fire separation follow. The full conversion takes considerably longer than the steelwork alone.
Do I need a party wall agreement for flat & HMO conversion steels in Hove?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.